Newspaper Blurbs about Lincoln Highway in Indiana

I spend a lot of time looking through old newspapers. It all started with my genealogical research. But I realized that this blog could benefit from the very same resources. And, if you have followed this blog, you know I do use them a lot. Today, I want to cover some newspaper articles about the early days of the Lincoln Highway, and construction of same.

The Indianapolis News of 18 June 1914 spent almost an entire column page to the Lincoln Highway. The majority of the article was about what Carl Fisher planned when it came to both the Lincoln Highway and the Michigan Road in his home state. Fisher was in South Bend, witnessing the beginning of work on his brain child. According to the News, he “has started another big movement. It is the improvement of the Michigan road from Indianapolis to South Bend to connect the speedway city with the coats-to-coast highway and to give central and southern Indiana an outlet to it.”

Plans were also to have a “General Good Roads Day” in Marion, Boone, Clinton, Cass, Fulton, Marshall and St. Joseph Counties. He was also calling for the oiling of that road. Calls for a state trunk road system were announced, as well.

The plans for the Lincoln Highway in South Bend called for an 18 foot cement road way with three foot graveled shoulders on each side, make for a total 24 foot wide road right-of-way. Fisher let the St. Joseph County Commissioners know that specifications only called for a 15 foot roadway, with the same three foot shoulders. This would make the right-of-way a total of 21 feet wide.

The cement mixture, according to Fisher, was also too expensive for the work. He recommended that the mixture include one part cement, two parts sand and three parts gravel. This was the same mixture that had been successfully in use in Wayne County, Michigan. This one change decreased the cost of construction of the Lincoln Highway across St. Joseph County from around $194,000 to roughly $150,000.

The Lincoln Highway was, at the time of this article, also completely marked across northern Indiana. Traffic along the new Auto Trail was increasing with travelers moving between the two coasts. The prospect of major traffic from the east going to the California-Panama Exposition in 1915 was on the minds of the people involved with completing the highway across the United States.

Fisher also expressed his concern that the Lincoln Highway be built “under competent engineers and honest contractors.” His belief that “nothing shows worse than concrete construction any underlying graft. It only takes two or three years to label a skimping contractor a thief or an incompetent.”

As a human interest story, less than a month later, in the Indianapolis Star of 19 July 1914, it was announced that “Fred Callahan, the young man who walked from New York to San Francisco and who is now walking back over the Lincoln Highway, reached Ashland, O., a short time ago. He averages about thirty miles a day and has covered more than 5,000 miles. He carries a pack on his back weighing about thirty-five pounds. Callahan says the Lincoln Highway is being put in good shape all across the country, and he ought to know.”

An article covering the entire Lincoln Highway in the Fort Wayne Journal-Gazette of 13 January 1918 mentions that of the 94 counties crossed by the Lincoln Highway in the United States, only one has completely finished the concrete pavement of the route. That county is St. Joseph, Indiana. The same article mentions that there is an official feeder road to the Lincoln Highway at Dyer. That feeder road connects the coast-to-coast highway to the city of Chicago.

The Indianapolis Star of 7 July 1918 mentions the work that the Indiana State Highway Commission made appropriations for that year. The ISHC, created in 1917, had taken the original route of the Lincoln Highway into the fledgling state highway system. It was called Main Market Road 2. According to the newspaper, $37,000 was allocated for the Lincoln Highway between Elkhart and the Elkhart-St. Joseph County line. The same amount was earmarked be Elkhart County. St. Joseph County was also starting the grading of the highway near Osceola. A contract for a new bridge in St. Joseph County was also let.

Tree planting was the news of the day in the South Bend Tribune of 25 June 1921. St. Joseph County planned to plant as many as 5,000 trees along the national highways that connected to South Bend. Keep in mind that both of Carl Fisher’s “children,” the Lincoln Highway and the Dixie Highway, met in South Bend. The roadside was “barren,” according to the newspaper. They also ran the following two pictures to make their point.

South Bend Tribune, 25 June 1921.

One of the bad things about looking through newspapers for a topic like the Lincoln Highway is that it was such an important feature in the United States that news from across the country would appear in the newspaper. Most of the coverage was for the national perspective, not the Hoosier one. I will continue to scour the newspapers of the state to find more information like this. Just that some projects are so large that local information is usually mainly ignored.

The Beginnings of Interstate 70 in Indiana

When I was younger, before I really started getting into becoming a road geek, the only road that I could tell you anything about was Interstate 70. It was the first one that I could remember. This was because I spent, at least in the back seat of the car, a LOT of time on that road. It was the first road that I remember learning things like exit signs and mileage markers. My family is from Pennsylvania. I describe getting to my ancestor’s location as driving on I-70 to the end, and keep going. (The end being New Stanton, PA. I-70 changes into US 119 there.) But, this is an Indiana Transportation History blog, not a history discussion about me.

Interstate 70 has been voted by some YouTubers the greatest of the cross-country interstates. The first newspaper reference that I have found about it came from the Muncie Star Press of 29 November 1957. The Headline read: “‘Interstate 70’ Name of New Highway.” The story went on to state “Federal Interstate Highway 70 is the name officially chosen for the projected New York-to-St. Louis federal super-highway that is to follow a course roughly parallel to U.S. 40. Its marked will be a shield with a red, blue and white background carrying the word Interstate across the top, the word Indiana at the bottom and in the center the figure 70.”

The National Road Traveler of Cambridge City reported, on 27 March 1958, that the Indiana Farm Bureau met with about 150 Henry County farmers to explain the rights of property owners along the new route. “The right-of-way for Interstate 70 will be 300 feet, which amounts to about 30 acres per mile.” The farmers were told that when considering the value of the property, keep in mind everything there – buildings, wells, septic tanks, fences and the cost of the land.

When the decision was being made about where to locate Interstate 70, there were a lot of things in play. Believe it or not, there were financial things taken into consideration. The plan was to put I-70 from 1.75 to 2 miles north of U.S. 40 According to the Tri-County Banner, Knightstown, of 6 February 1958, “highway engineers believe that the corridor between the two highways would be wide enough to constitute valuable industrial and business sites, conveniently located to rail as well as highway facilities.” Yes, you read that right. The location of railroad facilities was considered, at least in Indiana, for the location of the interstate.

Another thing mentioned in this article is that the plan was to try to use section lines as much as possible. Given the information put out, it would put the interstate, according to the newspaper, south of Spiceland. This would be located south of the Central School in the area. But the section line actually ran along the south edge of Spiceland, and through the school itself. That section line is located 2.5 miles north of U.S. 40. “Survey crews are already at work north of Richmond and it has been announced that the proposed highway will be slightly more than 2.6 miles north of U.S. 40 at Centerville, but will then swing slightly southward. The road will leave Wayne county about two miles north of U.S. 40 at Cambridge City.”

The Richmond Palladium-Item of 18 December 1958 reported “Record-Breaking Road Plan Includes Bypass.” The Chairman of the Indiana State Highway Commission was interviewed about the pending project. Chairman John Peters mentioned that the bids for the I-70 project at Richmond would be taken in March 1959. Right-of-way purchasing would also be started in early 1959. He also mentioned that three changes in the routing of the bypass, at the request of residents of both Richmond and Wayne County, have delayed the project for about a year.

This is just a small snippet of what went into creating Interstate 70 across, at least, eastern Indiana. At some point, I will be covering western Indiana. And the other interstates in the state.

West Marion County and I-465

This image has an empty alt attribute; its file name is images.jpg

The first part of the new beltway (almost) around Indianapolis started on the westside of Marion County. As mentioned in other articles, the original plan was to start Interstate 465 at Interstate 65 on the northwest side, with the replacement for State Road 100 (which I-465 officially was) heading south from there to circle around the county from there. Interchanges were planned at I-65, I-74/US 136, 10th Street, US 36 (Rockville Road), US 40 (Washington Street), Weir Cook Municipal Airport (Airport Expressway), Interstate 70, and SR 67 (Kentucky Avenue). According to USGS topo maps, like that included below, show that there was a stub ramp connecting I-465 to 62nd Street, although the ramp connecting to 62nd Street was listed as still proposed six years later.

1962 USGS topographic map showing the original interchange connection Interstate 65 and Interstate 465.

Construction started along the corridor in 1959. The Indianapolis News ran a series of pictures showing the plans set out by the State Highway Department. If you noticed the list of interchanges above, there were no plans for 56th Street or 38th Street to have ways to access 465. Bridges were to be built over 465 at 56th, 46th, 38th, 34th, and 21st Streets. (21st Street was a very special, and contentious, situation. I covered it in the article: “Building I-465 at West 21st Street. [8 May 2020]”)

Indianapolis News, 14 December 1959, showing the Indiana State Highway Department’s plans for the new Interstate 465 (also still called State Road 100 at the time) at the northern terminus of the highway.

The plans for Interstate 65 at that point were to continue to have it replace US 52 (Lafayette Road). The US 52 bypass at Lebanon was made part of the new I-65. The temporary plan was to connect I-65 just southeast of I-465 directly to US 52 until construction could continue. Then I-65 would also be US 52 from that point to northwest of Lebanon. I mention this only because the loop around Indianapolis was, apparently, easier to get approved than trying to run I-65 through town. (And since it would take another 16 years to complete, even to the point that an addition was planned to I-465 and completed before I-65 through Marion County says it all.)

It wouldn’t take long after the original plans for the interstate were laid down that changes were made. The non-planned 38th Street interchange was added to the deal. It was to be a partial cloverleaf interchange connecting to 38th Street at that point. Marion County had decided to build 38th Street from Lafayette Road east to the new White River bridge to be built by the city. At that point in history, 38th Street was a county road with nothing resembling the connections it has today as a major west side thoroughfare.

Indianapolis News, 11 December 1959, showing the future connection to 38th Street from I-465. This ramp would be built much later, when 38th Street was finally connected as a thoroughfare across Marion County.

The next interchange south of the “gonna be built someday” 38th Street was the connection to another interstate highway, Interstate 74. The plans shown in the Indianapolis News differ slightly from what was actually built. US 136 (Crawfordsville Road) is directly connected to the east end of the proposed interstate connection. This would change. It looks like the proposed interchange was moved slightly north, and Crawfordsville Road west of High School Road was turned north to connect to High School Road. This would be where US 136 would ultimately officially end.

Indianapolis News, 10 December 1959, showing the proposed connection between interstates 74 and 465. The original plan, and this was carried out, is that Interstate 74 would “travel over,” ISHD/INDOT term for multiplex, with I-465 from northwest to southeast Marion County.
1953 Topo map showing the intersection of West 10th Street and High School Road.

The next section did change, at least at one interchange, quite a bit. But before I describe that, let’s talk about the placement of I-465 from Vermont Street north to about where 16th Street would be, if it continued to High School/Girls School Road. The new interstate was planned, in that section, to be built directly over High School Road. This is not really a stretch, since High School Road, from Washington Street south to the Airport, was the original State Road 100. And I-465 was, for all intents and purposes, State Road 100 according to ISHD.

I have written a detailed history of SR 100 (SR 100: How did it come to be? [9 March 2019]) and an article about how, at one point, the connection between SR 100 on BOTH sides of Marion County were to have cloverleaf interchanges (“The Cloverleaf Interchanges at US 40 and SR 100” [20 November 2019]). If SR 100 had been completed on the west side, like it was on the north and east sides, I have no doubt that it would have followed High School Road north, probably, ultimately, to 86th Street, which was SR 100 along the northwest side.

The change in interchanges happened at 10th Street. The original plan was for a full cloverleaf interchange at that intersection. This would have pushed the eastbound 10th Street to southbound 465 ramp back closer to Glen Arm Road, where High School Road was rerouted to miss the interchange. What was ultimately built was a jumbled three-quarter cloverleaf with a flyover from westbound 10th to southbound 465.

In the end, High School Road was basically built over by 465 from Vermont to 10th Streets. 10th Street is a survey correction line, so High School actually moves slightly to the east at that point, as shown in the topo map to the left. For more information about survey lines, check out “Survey Lines and County Roads. (29 March 2019)”

Indianapolis News, 9 December 1959, showing the Indiana State Highway Department plans for I-465 from just south of the New York Central railroad tracks to just north of the Baltimore & Ohio Railroad tracks, including what was to originally be full cloverleaf interchanges at 10th Street and Rockville Road.
1953 USGS topo map of the area of Washington Street and High School Road. The area marked “Ben Davis” would be the location of the new cloverleaf interchange between US 40 and I-465.

From the looks of aerial photos in 1959 as shown in the Indianapolis News, the interchange at Washington Street was going to be very destructive. (Keep in mind that as of the writing of this article, MapIndy, my go to source for historic aerial photos of Marion County no longer offers that service. Maps are available, but the aerial photos are gone.) In addition to the shunting of Morris Street (a survey line and historic route of its own accord), most of where the interchange between US 40 and I-465 was basically what had been the town of Ben Davis.

Another thing would have to happen before this interchange would be built. It was determined, and reported, in July 1959 that an improvement of West Washington Street would have to occur before the interstate reached that point. US 40 was to be widened in the area. The work on Washington Street, however, would have to wait until sewer work in the area was completed…probably in 1961. Plans to widen Washington Street from 40 feet to 68 feet wide, with a four foot median and an eight parking lane on each side, were decided upon. Very little of that plan exists today…and if it does, it’s hard to find.

Indianapolis News, 8 December 1959, showing the proposed area of US 40 and Interstate 465.

The last area covered by the Indianapolis News in the series of articles (actually, it was the first since the editor staff decided to post them south to north, even though the interstate was built north to south!) shows the area of I-465 near Weir Cook Municipal Airport. The one change that I can see is what would become Airport Expressway (check out “Indianapolis’ Raymond Street Expressway” [4 February 2020] for the history of what started out as the Bradbury Expressway) was proposed to connect to the airport heading slightly north of due west, just above Southern Avenue. This section of the (now) Sam Jones Expressway is due east-west at the point it connects to Interstate 465. For a history of what is now Indianapolis International Airport, check out “Indianapolis Municipal Airport.” (20 August 2019)

Indianapolis News, 7 December 1959. This newspaper snippet shows the area of proposed I-465 near the (then) Weir Cook Municipal Airport (now Indianapolis International).

That covers the first of the construction of the State Road 100 replacement. I want to share this one last snippet from the Indianapolis News of 19 October 1960. It shows the construction of I-465/I-65/US 52 at 62nd Street…or the original northern end of Interstate 465.

Indianapolis News, 19 October 1960, showing the original northern end of Interstate 465.

INDOT’s Reference Post System

In 1999, the Indiana Department of Transportation decided that it was time to come up with a system that would help better keep track of features along the roads that for which it was responsible. While is would be based, according to INDOT, on the mileage of the road, it was not a milepost system. It was a locator for maintenance items, other than signs, on the state highway system.

RPS 86 on US 40, Marion County, Indiana (Washington Park Cemetery). From Google Maps, snipped 23 December 2020.

There are many parts to the system. The one that most people would have seen, but not really noticed, were the signs that were put up for use with the system. These consisted of small blue signs with a mile number on it, with a smaller sign, if needed, below it with an offset to that mile on it. The signs themselves were barely wider than the post they were on. Very small in relation to most highway signs. Since they are technically only for INDOT use, their size wasn’t a concern. The public wouldn’t notice them, lessening the sign pollution that departments of transportation have been trying to keep under control forever.

RP 88, Offset .88, US 40 bridge of Buck Creek, Cumberland

I really wish I could have had a better snippet for the offset post, but then, the idea was to give the reader the image of what they roughly look like, so the reader would know what to look for.

The RPS manual is very detailed in its information. For instance, the picture to the left is listed as “RP_U_40_Post_86,” meaning “Reference Post, US 40, Post 86.” The one on the right is listed as “CUMBERLAND CORP. LINE BR 4588 O BUCK CREEK,” at least in the 2004 manual.

US 40 is a very prime example of why this system isn’t to be used as a mileage post system. The system was setup prior to the 1 July 1999 decommissioning of US 31, SR 37 and US 40 inside the Interstate 465 loop. What was, in 1999, marked as mile 86 on US 40 is, in 2020, at mile 92.37 on that very same road in 2004. In 2016, the last update from INDOT, it was listed as US 40 mile 65.179. The legal definition of US 40 was lengthened when it was rerouted along the southside of Indianapolis on I-465 in 2004. By a little over six miles. By 2016, the extra mileage along I-465 was removed to show a more accurate road mileage count towards INDOT’s limit of 12,000 miles.

But there is a bit more to the reference post system that comes into play. Each highway listed in the RPS not only includes the complete mileage for the road in Indiana, but they are also listed by the mileage per county, as well. For instance, reference post 86 above is listed as Marion County mile 24.06 in 2004. In the 2016 manual, that mileage is 5.027.

Then, the reference post system records almost everything along the road. This includes EVERY village/town/city street that intersects with the posted road. For instance, near reference post 86 is, in the 2004 manual, “86 + 0.21 24.52 IR 4193 LT (DELBRICK LN).” At reference post location 86.21, 24.52 route miles into Marion County, Delbrick Lane connects to Washington Street (US 40) on the left (north) side of the road. Directions are listed from the increasing number of the reference post. Every street is listed, although almost none of them have a reference post sign.

Also, the corporation limits of towns and cities are listed by the reference post location, although there is no reference post installed most of the time. This even includes old corporation limits. For instance, in the 2016 manual, reference post 85+0.686 is listed as “City or Town Limit – Indianapolis.” Post Road is reference post 86+0.668. Legally, Indianapolis continues for another at least two miles (the sign welcoming one to Indianapolis is west of German Church Road, the county line is another mile east of that, but that is in the town of Cumberland. And even legally, Cumberland is part of Indianapolis. It is as confusing as all get out, but suffice it to say, for the past 50 years, the city limits of Indianapolis have been the county limits of Marion County, with some exceptions. Certainly not Post Road.

But the idea of the legal multiplex of I-465 with almost every INDOT road in Marion County (there are two that don’t mix with I-465: US 136 and SR 135) that brings up another question. What about multiplexes of state roads?

When the system was created in 1999, it was designed with a hierarchy of roads. That hierarchy was interstate, US highway, then state road, in that order. INDOT does not use the term “multiplex” officially. It is called “travel over” in Indiana. The following picture comes from the INDOT RPS guide of 1999 showing how “travel overs” are handled when it comes to marking the mileage of the road.

Indiana Department of Transportation Reference Post System Users Guide, May 1999.

As you can see, near Frankfort, US 421 takes precedence with the little blue signs. SR 39 is junior to SR 38 when it comes to the signs, only due to the fact that 38 is before 39 numerically.

The system underwent some changes between 2004 and 2015. In 2015, it was made perfectly clear that the manual may contain some mistakes, but that every effort was taken to avoid them.

There was also a special note involving US 40 in Vigo County. When US 40 was removed from most of Vigo County, and rerouted along I-70 and SR 46, the RPS system was not changed to reflect that. The section of US 40 that “travels over” SR 46 is still labelled as SR 46. Here is INDOT’s explanation: “US 40 in Vigo County has a special issue that needs to be addressed. Due to relinquishments and creating a travel over for US 40, the alignment does not follow the historic path. US 40 now traverses where SR 46 has traditionally been and SR 46 is considered the Travel Over on US 40. However, the existing reference posts are still for the SR 46 route and are running in a contrary direction to the increasing direction of US 40. Therefore, for the purposes of this book, RP and Offset for the first 3 miles of US are based on the State Log Measure until it reaches the traditional location for US 40 and then jumps to RP 11 + 00 at the intersection of SR 46 and US 40.”

I mentioned above about the original system being put in place prior to the decommissioning of routes in Marion County. It is important to note that there were more routes affected than just those that were moved to I-465. Those routes were US 31, SR 37 and US 40. The mileage on those roads got weird, yes. But there were two others that were affected by the change…and one most people didn’t even realize.

SR 135 was rerouted from Troy Avenue to Thompson Road, cutting two miles out of the official route. This just required moving the little blue signs from north of Thompson Road, and surveying what else would need signs. And what wouldn’t.

The other route affect wasn’t even marked when it was decommissioned. Shadeland Avenue on the east side of Marion County was still legally SR 100 from I-465 to US 40 (Washington Street) until 1 July 1999. For the longest time, the only marker on SR 100 was a smaller blue sign below the reference post signs that read “100.”

INDOT has available on their website the RPS manuals for 2004, 2015 and 2016. Also available is the users guide from 1999. Here are the links for each: Users Guide200420152016

Original SR 31 and the Pike’s Peak Ocean-To-Ocean Highway

Just a short post to show how state roads have changed.

I have covered Auto Trails and the original state road numbers several times over the past nearly two years. I had done a post about the rerouting of the Pike’s Peak Ocean-To-Ocean Highway through Indiana. But the original route, as covered by fellow blogger (and ITH Facebook Group co-admin) Jim Grey, traveled across the western part of the state using the US 36 corridor. (The latest is “US 36 and the Pikes Peak Ocean-to-Ocean Highway in Danville, Indiana,” among others) I’d like to say it followed the current US 36, but it’s been moved several times over the years.

As I had mentioned in other posts along the way, many of the roads that were added originally to the state highway system were part of the Auto Trails systems that crossed the United States. When the Pike’s Peak road was taken into the state system, it was given the designation “State Road 31.” Well, sort of.

OSR 31 started in the west at OSR 10, across the Wabash River west of Montezuma. From there, it went through Montezuma, Rockville, and Bainbridge to Danville. From Danville, the PPOO rumbled across Hendricks and Marion Counties along what is now Rockville Road (and Rockville Avenue – because Rockville Road didn’t connect to Washington Street directly until later). The original SR 31, however, connected to the National Road (then Original State Road 3) at a completely different location.

Strangely, the route of the original SR 31 is now not part of the state highway system. Current SR 39 leaves Danville via Cross Street south towards Martinsville. Original State Road 31 turned south from Main Street on Jefferson Street. Jefferson Street turns into Blake Street, then Cartersburg Road. The state road connected to OSR 3 southeast of Cartersburg.

The drive from Danville to Cartersburg is quite a nice one.

With the Great Renumbering in October 1926, original state road 31 became US 36. Again, sort of. The section from Danville to Cartersburg was removed from the highway system at that time. US 36 continued on into Marion County, as shown in the article “Road Trip 1926: US 36.” Just like the original eastern end of OSR 31, the original eastern end of US 36 is now gone, ending at a parking lot.

I also covered a reroute that was put in place along US 36, after the Great Renumbering, at Bainbridge.

1952: Another New US Highway

Between 1951 and 1952, there were a lot of highways that were added to the US Highway system by the AASHO, or American Association of State Highway Officials. The main reason for this was, quite honestly, “tourist roads.” That was the purpose of expanding US 421, mentioned in my last post, from Tennessee to Michigan City. Another addition was US 231, which crosses the state from Owensboro, Kentucky, to Lake County, Indiana.

At the time, the two major US Highways that crossed Indiana, US 31 and US 41, were very busy doing what they do best – moving travelers north and south. Both highways start in northern Michigan, with US 41 beginning in the Upper Peninsula, US 31 starting at Mackinaw City. At the other end, US 31 ends in southern Alabama, US 41 end at Miami. Both highways were essentially “tourist roads.”

Since US 41 connected Chicago and Miami, it was the US highway replacement for the Dixie Highway. And as such, was very busy. AASHO decided that it would be a good idea to create another south bound highway to funnel off traffic from the two major roads crossing Indiana. That road would be US 231.

The Lizton Daily Citizen of 17 September 1952 mentions that the new route markers for the newest US highway in Indiana were in stock and to be replaced over the next month or so. It was also mentioned that the state road numbers that were assigned to route that would become US 231 would still be there after the marking of the US route. “The newly-designated U. S. 231 will travel from Chicago, Ill. to Panama City, Fla. It is to be called a ‘tourist’ highway and is designed to relieve overloaded U. S. 41 of some of its traffic.”

US 231 started life in 1926 with the creation of the US Highway system. At the start, it began at US 90 near Marianna, Florida. Its northern end was at Montgomery, Alabama. The first expansion of the road had it ending in Panama City, Florida.

US 231 crossed into Indiana from Owensboro, Kentucky, on what was then SR 75 (now it is SR 161), then east on SR 66 to Rockport. From there, it would follow SR 45 to near Scotland, SR 157 to Bloomfield, west on SR 54 to SR 57, then north on SR 57 to its junction at SR 67.

From the junction of SR 57 and 67, the new highway would follow SR 67 into Spencer, where it would be joined with SR 43. From here, it would follow (replace) SR 43 north from Spencer to Lafayette.

Now, here is where the description of the highway in the newspaper and the actual route differ. According to the route published in the newspaper, the route would follow SR 43 all the way to Michigan City, ending there. Well, it was already mentioned that it would end in Chicago (which, by the way, it never did), not Michigan City. Also, again, as mentioned in my last blog entry, US 421 took SR 43 into Michigan City.

At Lafayette, US 231 would multiplex with US 52 to Montmorenci, where it would turn north on SR 53. Now, for those of you keeping score with the US highways in the Hoosier state, this is where, from 1934 to 1938, there was another US highway that had been removed for being too much of a duplicate. That highway, US 152, used the US 52 route from Indianapolis to Montmorenci, where it replaced SR 53 (which it was in 1933) all the way to Crown Point. In 1938, with the decommissioning of US 152, the road reverted to SR 53 again.

And in 1952, that designation was once again removed for the placement of US highway markers. This time, US 231. But, the state road number wasn’t removed immediately this time. And US 231 rolled its way along SR 53 until it entered Crown Point. From there, it connected to US 41, the road it was supposed to help relieve traffic, near St. John using what was then SR 8.

For the most part, with the major exception of two places, the US 231 route is the same as it was back then. There may have been some slight moving of the road, especially near Scotland for Interstate 69, but the minor revisions are few and far between. The major relocations are definitely major. A complete reroute in the Lafayette area, which has US 231 bypassing both Lafayette and West Lafayette. It has, in recent years, taken to carrying US 52 around the west side of the area, replacing the much celebrated US 52 bypass along Sagamore Parkway. I will be covering that bypass at a later date. Let’s just say that there was a lot of newspaper coverage of that at the time.

The other major change in the route is near the Ohio River. A new bridge spanning the river was opened in 2002. The new bridge, called the William H. Natcher, is located north of Rockport. The original US 231 route, which followed SR 66 to due north of Owensboro, Kentucky, is now SR 161 between SR 66 and the Ohio River. It should also be noted here that at Patronville, SR 75 (US 231 now SR 161) had a junction with SR 45…the route that the new US highway would follow from northeast of Rockport to Scotland. Now that junction is just with Old State Road 45.

Due to its route across the state, at 297 miles long, US 231 is the longest continuous road in the entire Hoosier State. That may seem wrong, but consider that Rockport is actually south of Evansville…and the route through the state is nowhere near straight.

1930: A New Bridge over the Wabash at East Mount Carmel

Atlantic-Pacific
Highway marker

East Mount Carmel, Indiana. A train stop along the Southern Railway connecting Louisville, Kentucky, to St. Louis, Missouri. The town was also located on an Auto Trail called the Atlantic-Pacific Highway. Across Indiana, it would connect East Mount Carmel on the Wabash to Cincinnati via Princeton, Jasper, Paoli, Salem, Scottsburg, Madison, Vevay, Rising Sun, and Lawrenceburg.

But at East Mount Carmel, traffic was still fed across the Wabash River via ferry. As mentioned in other articles here on Indiana Transportation History, getting a bridge across the Wabash or the Ohio River, given that it would cross a state line (usually – the US 41 bridges actually are all in Kentucky, although they cross the Ohio), was a long process that often met with delays.

Hope was to be had when it was announced on the front page of the Mount Carmel (Illinois) Daily Republican-Register of 10 April 1930 that “Bridge Will Soon Span Wabash – Illinois-Indiana Highway Bridge That Will Span the Wabash River at Mt. Carmel.”

The bridge was the work of many years of planning. The State of Indiana wanted a bridge at Vincennes. They also wanted the State of Illinois to help with the cost. Illinois, however, had other plans. They wanted a bridge at Mount Carmel. And Illinois wanted Indiana to help pay for it. Neither state would budge on their plans…until the agreement was made that both bridges would be built.

Money for the Mount Carmel bridge was allotted by the Illinois General Assembly in 1927. A total of $225,000 was set aside for the construction. This new bridge would connect Illinois State Road 1 and Illinois State Road 15 to the Indiana State Highway system. This would become an extension of Indiana State Road 64.

The new bridge would be located 1000 feet south of the Southern Railway bridge that crosses the river near Mount Carmel. It would consist of a 22 foot wide roadway on twelve 225-foot spans. The bridge would provide 25 feet of clearance from the low steel to the high water mark of 1913. The Illinois approach was to be built at an elevation of three feet above the 1913 high water mark.

10 Apr 1930, Mount Carmel Daily Republican-Register

The bridge would be completed in 1932. By 1985, the bridge had fallen into disrepair. A plan to renovate the bridge was created while waiting for both Illinois and Indiana to decide to replace the bridge…which it did. The new bridge was placed just south of the original bridge.

Adeway

Many highways were given names in the Auto Trail era. One that always intrigued me, and I have yet to find a good history for, is a road that led from Indianapolis to Chicago. It was called the “Adeway.” The best map of the route that I have found, however, shows the road only going from Crawfordsville to Chicago. That map is from 1923, and is available at the Indiana State Library online.

The Adeway left Crawfordsville via Lafayette Avenue, traveling northeast before coming to Old Oak Hill Road near the intersection of current US 231 and Lafayette Avenue. The old auto trail would follow Old Oak Hill Road, and Oak Hill Road, until it becomes what is now Old State Road 55. It would follow what would become SR 55 in 1932 all the way to just east of Wingate. The original route crosses private property now, as it would connect directly to Crawfordsville Road in Wingate. Today, it turns west onto Wabash Street. The Crawfordsville Road intersection has been moved to make a perpendicular junction between the two roads. The original route can still be seen in grass markings in the following Google Maps snippet from 25 October 2020.

From Wingate, the original Adeway would follow what is now SR 55 to Newtown. From Newtown, the road would turn north along what is now SR 341, following that current state road to what is now SR 28. The auto trail turned west along the current SR 28 to Attica. At Attica, instead of turning onto Jackson Street, as SR 28 does now, it continued along Main Street, then Mill Street, and would cross the Wabash River along the old Mill Street bridge. The current state road, and US 41, crosses at Jackson Street.

After crossing the Wabash, the original auto trail would turn on what is now Old SR 55…but that route goes into private property today. It is best to use current SR 55 north of US 41 to approximate the old road. There are places where the current state road was straightened for ease of use and safety, but it is still very close to the original country road that would become part of the Adeway.

At Warren County Road 600 North, the Adeway turned west. It would curve several times, then turn west again on Warren County Road 650 North heading towards Rainsville. The old highway follows what is now Rainsville Road to just before SR 26. The road had been moved for safety at this point. The old Rainsville Road was part of SR 26 before the move. It can be clearly seen on this Google Map snippet of 25 October 2020.

The Adeway then turned north along what is now Meridian Line Road, right at the end of the current bypassed section. This would take travelers (mostly) due north through Fowler, where the street is still called Adeway. After crossing the current US 52, the street becomes known as Washington Street, but also happens to be SR 55 once again for its trip northward through the Benton County countryside.

In an effort to maintain its own way, the Adeway would turn west on what is now Newton County Road 1700 South. This is one mile south of the Illinois Corn Belt Route, which would later become part of US 24 across northern Indiana. The highway would follow SR 1700S until it would turn north along what is now US 41, travelling into Kentland.

Although the road had been straightened in places, the US 41 route approximates the old Adeway route. At Benton County Road 900 South (which east from US 41 is SR 16), the Adeway turned west again…to enter the town of Ade. One might assume that this is where the road got its name…but I am not going to jump to that conclusion until I have more facts.

From Ade, the old highway followed CR 275 West and CR 300 West north through Morocco and onto what is now US 41 (again) northward to Enos. The distance from Ade to Enos is 10 miles according to the Rand McNally Auto Trails Map of 1920. At Enos, the old route leaves the current state highway system again, this time for a short jaunt along CR 100 North to CR 400 West. Five miles later, the old route turns east, along CR 600 North, to connect to CR 300 West, which is still US 41. Just north of the intersection of US 41 and CR 600 North was a place called Conrad. The name still exists there, but not as a town of any kind.

The Adeway still follows US 41 north until just south of Lake Village. Here, the new road bypasses the town, while the old road, called Old 41, enters the town, as did the Adeway. North of Lake Village, the old road connects back to US 41, but doesn’t share that route long. Just south of Schneider, US 41 veers off to the northwest, while the old route continued straight through the town along what is now Parrish Avenue. At what is now 219th Avenue, the Adeway turned east, then north again along what is now Austin Avenue for its journey towards Lowell.

The journey continues along Austin Avenue until the junction of Belshaw Road, where the Adeway turned northeast to Cline Avenue, one-half mile east of Austin. The route entered Lowell on Cline Avenue, but left on Morse Avenue. Here the old highway followed Morse Avenue north and then west along the northern edge of Cedar Lake. It followed what is now Lake Shore Drive until it turns into 135th Avenue. There, it followed what is now 135th Avenue west across US 41 again, until Calumet Avenue near Brunswick.

Turning north along Calumet Avenue, the next turn would be at what is now 101st Avenue near Keitzburg. West along 101st, the Adeway then turned north again on what is now Sheffield Avenue. It then followed Sheffield Avenue/Hart Avenue (Dyer)/Sheffield Avenue until it became what is now Columbia Avenue. The old route then connected back to Calumet Avenue, which it followed all the way up to Indianapolis Boulevard, for a northwesterly turn towards Chicago. From the connection of Columbia and Calumet Avenues, the road is not part of the state highway system. At I-94, Calumet Avenue becomes part of US 41, and the Adeway follows that road designation into Chicago.

As is typical of the Auto Trail era, the journey of the Adeway from Crawfordsville to Chigago is nowhere near a straight journey. It winds through the northwestern Indiana countryside, meandering its way from point a to point b. But it would make one heck of a road trip, should one want to do such a thing.

A Quick Look At Today’s State Roads, From A Historical View

A Facebook direct message from a reader of the blog started the research bug going again. Now, while I am still looking up information on his particular subject (transportation to Center Valley in Hendricks County, particularly a possible railroad there), part of his subject did come up. As well as a few others. Today, I want to look at the things that I have found while researching that topic…while not finding much about the topic.

The “town” of Center Valley is along the route that would become State Road 39 just north of the Morgan-Hendricks line. A post office existed there from 1855 to 1902. But what is important is the route that rumbles north to south through the town…the aforementioned SR 39. It wouldn’t be until 1932 when that section of SR 39 was added to the state highway system. But, the designation “state road” goes back quite a bit…like 1833.

The 17th General Assembly of Indiana passed into law several state roads. The first I want to mention would be the one that would make Center Valley (or, more to the point Centre Valley) a place. The route that would eventually become SR 39 was built as the Martinsville-Danville-Frankfort State Road. The southern end would be part of the state highway system from 1920 – the bridge over White River west of Martinsville. The northern end would be part of original State Road 6, connecting Lebanon to Frankfort. As original SR 6, it would become SR 39 with the Great Renumbering.

Two more state roads would from Martinsville would be added to Indiana with this meeting of the General Assembly. The first is one that would not become part of the state highway system. It was described as “an act to locate a state road from Martinsville, in the county of Morgan, by the way of Cox’s mill and Solomon Dunagan’s, in said Morgan county, to Stilesville, in the county of Hendricks.” This is an example of how the General Assembly would set up a “state road” through a particular person’s land. I would assume that what is now Tudor Road, southeast of Stilesville, was part of this road.

Another state road project including Martinsville did make it to the state highway system… eventually. The act created “a state road from Martinsville, in Morgan County, to intersect the state road leading from Madison to Indianapolis, at Edinburgh, in Johnson county by the way of Morgantown in said Morgan county.” This state road would be added back into the state highway system in the 1930’s…as State Road 252. A history of that road is available from ITH here.

But Martinsville wasn’t the only beneficiary of that particular meeting of the General Assembly.

A state road was created by the General Assembly to connect the town of Lagrange, in Tippecanoe County, to Logansport, in Cass County. Where is LaGrange? Well, it was a town along the Wabash River at the Warren-Tippecanoe County line. It was founded by Isaac Shelby in 1827…and had a post office from 1832 to 1835. It’s prime was with the Wabash Canal during the riverboat era. When the Wabash Railroad was built on the opposite side of the Wabash River, the town of LaGrange just dried up and disappeared.

Another road that was created at that time would connect Williamsport to the Illinois-Indiana State line via Lebanon (sic), now West Lebanon, and the now abandoned town of Chesapeake (about two miles east of Marshfield). This route will require some research.

Part of the road that would become, in time, SR 46 between Newbern and Bloomington would be added as a state road in 1833. The original road would start at the Michigan Road in Napoleon, travel through Camden (unknown today), Newbern, and Columbus to Bloomington. The section from Newbern to Columbus was part of the state highway system as SR 46, until INDOT truncated SR 9, turning the old SR 9 into SR 46.

Stilesville would be mentioned again as a state road was created to connect it to Crawfordsville via New Maysville.

The last road for this article would be a road that is still in existence, more or less, but not part of the modern state highway system. The description of the act was “to locate a state road from Green Castle, in Putnam county, to Carlisle, in Sullivan county, by way of Manhattan in Putnam county and Bowlingreen and New Brunswick, in Clay county.” Some day, I want to do more research on this road.

US 41 in Gibson County

Princeton, IN-IL, 1:62,500 quad,
1903, USGS

While looking through old USGS topo maps, I found one that caught my interest almost immediately. I have talked over the past year or so about how the current state roads came to be as old county roads from early in Indiana’s history. One that shows this very well is what would become SR 10 in 1919 and US 41 in 1926.

The map to the left shows the county roads between Fort Branch and Hazelton in 1903. Yes, 1903. This is the USGS map, 1903 Edition of the Princeton, Indiana, 1:62500 scale. I have used Microsoft Paint to draw lines of two colors on it. The green lines show where US 41 is today, using the roads as they were in the turn of the 20th century. The blue lines show roads that would be, through history, part of US 41 before it was bypassed. The area in Princeton is harder to nail down, so I included two routes through the town. Both are possible, and since at the time of this map there was no US 41, it didn’t matter which way travelers went.

Historical Topographic Map
Collection, 1942, USGS

As is typical of the USGS, no new maps were truly drawn after 1903 at this scale…at least none that are accessible. What is shown to the right is the 1903 map updated to 1942. It shows several changes in the routing of US 41 between its creation in 1926 and 1942.

First, starting at the top, is the Hazelton Bridge. Construction started in 1921 to replace a ferry near that location. The bridge, as mentioned in the link above to another Indiana Transportation History article, carried SR 10 (and the Dixie Bee Highway, as it was known at the time) over the White River near Hazelton. The bridge was massive. Said to be one of the largest ever built (to that time) by a state highway department in the midwest.

Another section that would be moved before 1942 would be south of Patoka. The road that is now Old US 41 between Princeton and Patoka is actually a replacement. During the 1930’s and 1940’s, the Indiana State Highway Commission made it a point to shorten and straighten state highways. A lot of this put the new location of the state highway next to a section of railroad tracks.

If you have any doubt about this building technique, check out SR 67 southwest of Indianapolis (Kentucky Avenue – moved 1936), SR 67 northeast of Indianapolis (Pendleton Pike, or actually, its replacement), SR 44 from Shelbyville to Rushville (railroad tracks were in place until 1980 or so), and SR 135/252 from Trafalgar to Morgantown (road was built around 1940-1941, tracks were abandoned at very near the same time, although some remnants of those tracks still remain 80 years later).

US 41 would run beside the Chicago & Eastern Illinois tracks between Princeton and Patoka, entering Princeton north of the old route by about two blocks. South of Princeton, the old route was followed toward Fort Branch.

Historical Topographic Map Collection, 1962, USGS

By 1962, several changes were made again to US 41. From Patoka to Hazelton, the route was moved to its current location, replacing the old Hazleton bridge and widening and straightening the road most of the way. There was one section of road that was still two lanes according to the USGS maps of 1962…and that was being rectified.

The old Hazelton Bridge remained in place for years after its replacement by the Indiana State Highway Commission. It would be given to the counties for their maintenance.

At the same time, the current routing of US 41 was also completed. The USGS shows the year of the map as 1961 on the Princeton 7.5 degree quad. (The map to the left is the 1962 update of the 1959 Patoka 7.5 degree quad.)

The major point of this article is to show how the country roads looked in 1910, and before the state started taking over, to give an idea of how one got from point A to point B at that time. These maps, especially those of 1903, really show off the routes that were depended upon early in the history of Indiana. It also shows that, in Indiana, the fastest way between two points is not always a straight line.

US 50 West from Aurora

Today, I want to focus on US 50 on the other side of the state. Yesterday, I covered the original US 50 from Vincennes to Wheatland. Today, the last eight miles heading into Aurora. When the Indiana State Highway Commission was created in 1917, the future US 50 was included…but not as a single road. From Mitchell north to Bedford, then east, it was original state road 4. From Mitchell west, it was original state road 5.

The other thing I want to look at it the location of the original road. Unless you have driven in that section of Indiana, it is hard to fathom the difficulty in building a road through southern Indiana. Most of the state is (relatively) flat. Along the Ohio River, not so much. As someone whose family came from Pennsylvania, I realize the sheer insanity of building a road where the land has to be followed…not plowed through.

In northern and central Indiana, most roads can be built in a straightish line. Obviously, there are hills one has to skirt, and rivers to cross. But most of the land is relatively flat. That ends about 40 miles south of Indianapolis. And abruptly. I am only going to use snippets from one map (and a quick Google map) for this post…that of the 1943 USGS Topographic Map of the Aurora, Indiana, quadrangle. I have made five snippets…one a complete overview, and the other four are basically two miles at a time. I will be going from east to west in this case.

I know this is hard to see. That is why I have broken it down into smaller chunks. But this gives the overview of the whole area. Consider that each of the brown lines on this map are 10 feet changes in elevation. This gives a whole new meaning to up and down, eh?

The original US 50 entered Aurora from the north on what is now Main Street. North of Hogan Creek, Google Maps lists it as George Street. Where George Street meets US 50 north of Aurora, US 50 pretty much follows the old path, for a while, on its way to Lawrenceburg. A turn west on Third Street, and following the old road is still possible. Another turn south on Bridgeway Street, then west on Fourth Street, then original US 50 leaves the small burgh of Aurora. Google Maps shows the old road as Conwell Street. Before it connects into the current US 50, it turns south on Indiana Avenue, still staying south and east of the current US highway.

The problem with following the old road from here is that it has been cut off from the rest of the highway system. Indiana Avenue, before it would connect to current US 50 again, it curves east away from its old path. The Google map snippet to the left shows a blue line where the old road crossed the area that is now US 50, changing from what is now Indiana Avenue into Trester Hill Road.

As you can see from the topo maps of before the new road was built, the frontier path, later state road, that became US 50 originally skirted the edges of the topographical lay of the land. Without looking closer, I can not tell if it is a valley or the top of the ridge that the old road follows. A look on Google Earth shows it may be a valley that the road is keeping to.

The last four miles that I will be covering in this entry are pretty much using the old road as it was created in the early to mid 1800’s. Yes, the road is that old. The area that the road follows is called the Mount Tabor Ridge on this map. And the old road tries to keep climbs and descends as small as possible. This made sense, since getting horses, or even worse, oxen, to climb a hill was a chore in itself. Now, add a wagon, or saddlebags, and it got worse. There are stories abound that tell of someone hurt, or worse, killed trying to traverse steep hills.

This map shows the end of today’s coverage area. Not that I don’t want to keep going west from here. The next topo map available is the Dillsboro quadrangle, but it is dated 1958.

Following the original US 50 through the area gives an idea of what was required when a road was commissioned to go from point A to point B. Just looking at this route shows why the first team that went into “the wild” when it came to building a road would be the surveyors. Of course, this has always been true, for any road built in history. It wouldn’t have been good to draw a straight line on a map and just told someone to build that straight line. Especially through the landscape of southern Indiana.

Indianapolis: Indiana Avenue Bridge Over Fall Creek

Early in the history of town of Indianapolis, when the state started building roads to connect the fledgling capitol to the rest of the state, a road was built from the northwest corner of the original Mile Square, traveling northwest. That road would be called both the Lafayette Road and the Crawfordsville Road, since it went to both. After the road crossed Fall Creek one mile north of the center of the town, it took a route closer to White River. That section would later be called Speedway Avenue and Waterway Boulevard. But the bridge over Fall Creek, connecting the two sections, would take nearly two decades for a true resolution. And it required the removing of several streets, including the historic Lafayette/Crawfordsville Road.

1937 MapIndy Aerial photograph of the Indiana Avenue & 10th Street area.

The bridge is question is shown on the above 1937 MapIndy photo. At that time, the intersection at the bridge was a confusing jumble of streets running in different directions. At what became the intersection of 10th Street and Indiana Avenue, there were also connections to Locke Street (heading south past the City (Wishard) Hospital, and Torbett Street running north of 10th heading east. Many people still referred to 10th Street between this intersection and the White River Parkway as Fall Creek Parkway…but that was its old name by the time this photo was taken.

Indiana Avenue had become a major route for people leaving downtown Indianapolis for the northwest suburbs. The northern end of both of Indiana and Speedway Avenues were connected to 16th Street, which ran west from Indiana Avenue to the Emrichsville Bridge over White River. The state had connected separate sections of 16th Street from Indiana Avenue east to Northwestern Avenue as part of State Road 34. Traffic, therefore, was heavy across the bridge.

That was until the summer of 1936.

It was then that the city of Indianapolis limited the bridge traffic to five tons. Trucks and busses found themselves having to go around the closed bridge by using 10th and 16th Streets. In the fall of 1938, the bridge was closed completely to all traffic. Street cars found themselves now being rerouted around the snarl. Indiana and Speedway Avenues north of Fall Creek simply became cul-du-sacs because they had no southern end at all.

The Indianapolis News of 7 May 1943, in an editorial piece, mentions that in 1936, when trucks were banned from the bridge, the Board of Works announced a $110,000 plan to build a new bridge on the site. “In the fall of 1938, the bridge was closed to traffic and a year later the city was promising solemnly to produce a new one almost immediately.”

That was followed in the fall of 1940 by the City Council and the City Engineer coming together to talk about building a new bridge for Indiana Avenue. The City Engineer was “ordered to determine ‘by the next meeting’ the precise status of the matter.” That went nowhere as it was in 1941 that a discussion was held about finding an old bridge from somewhere else to replace the old Indiana Avenue bridge that had, at that point, been completely closed to traffic for three years.

As mentioned above, the editorial was run in the News in May 1943. The bridge was still closed to traffic.

A week later, on 12 May 1943, the Indianapolis News ran another editorial on the same subject. “Mayor Tyndall expresses in one short sentence what many have had in the back of their minds for years about the Indiana avenue bridge over Fall creek. ‘If the army had to cross it, the bridge would be fixed over night,’ he declared. The bridge has stood year after year, closed to all but pedestrian traffic, while tens of thousands of motorists and others have been forced to detour by way of West and Sixteenth streets to get to the baseball grounds and parts of the city northwest of there.”

The News goes on to mention that many times over the past four and a half years, attempts have been made to remedy the situation. Without result. Some of the blame was placed on pending flood control and prevention improvements to Fall Creek. Those improvements still hadn’t happened. The News was advocating for a solution to the bridge issue sooner than later.

And action was taken when Mayor Robert H. Tyndall cut the ribbon on 1 November 1944 to open the newly repaired Indiana Avenue bridge over Fall Creek. Traffic could begin moving across the facility again. Trolley traffic on the Riverside line would start again on 27 November 1944. And everything was great. For almost six years.

The headline in the Indianapolis News of 24 March 1950 read “Indiana Avenue Bridge Out for Baseball Fans.” Simply, it meant that the old bridge over Fall Creek was closed to traffic again. The sticking point, again, came down to whether to spend $35,000 to patch the bridge, or wait until the flood control improvements made it a requirement to replace the bridge. The flood control project, which was estimated to be around $1,000,000, was still in the works as it had been since the early 1940’s.

As it turned out, less than a month later, the city council voted to appropriate $120,000 to fix the old bridge. This was required before bidding could begin on the the contract to fix it. It would seem that it would take longer than expected. It became a political issue when, in October 1951, just prior to the Marion County elections, the political party in charge was blasted for not taking care of a bridge that not only served baseball fans and residents of the northwestern section of the city, but served as an emergency route to Wishard Hospital, which sat just south of the bridge.

The Indianapolis Star said it best in the first paragraph of a story with the headline “City To Spend $120,000 For New Bridge” on 9 April 1952. That first paragraph read “the city is going to sink $120,000 into a new bridge which may be torn down within three years.” While Mayor Clark of Indianapolis was telling the City Engineer to rebuild the bridge, he was also telling the engineer to continue looking into getting Federal money to move Fall Creek 100 feet to the north as part of the flooding control and prevention program.

The flood control issue would finally be resolved in 1959. On 9 August 1960, the old Indiana Avenue bridge was closed once again, this time for good. The bridge was immediately closed and dismantled. It would be replaced by a four lane facility. The flood control project would also require the creek to actually move 100 feet to the north of its then current position, a rerouting of Speedway Avenue, to be renamed Waterway Boulevard, to a new connection with Stadium (Indiana) Avenue two blocks northwest of its historic location, and a removal of Locke Street and Fall Creek Parkway East Drive for the intersection at 10th and Indiana. (The old Torbett Street had long before been cut off from the intersection, becoming a driveway for the old YMCA that stood on the northeast corner of Fall Creek Parkway and 10th Street.)

17 July 1961, Indianapolis News

The new channel for Fall Creek and the new Indiana Avenue bridge was completed in July 1961, as shown in the above photograph from the Indianapolis News of 17 July 1961. The bridge would be opened to traffic as soon as reconstruction of the intersection at the southern foot of the bridge was completed on 1 August 1961. The below MapIndy aerial photograph from 1962 shows the reconfiguration of the intersection, the new location of Speedway Avenue, and the removal of the ends of Locke Street and Fall Creek Parkway East Drive.

1962 MapIndy aerial photo of the area around the Indiana Avenue bridge over Fall Creek.

I-65 and I-465 On The Northwest Side – A Pictorial History

Today, I want to use MapIndy and USGS Topographic maps to show the progression of the interchange between I-65 and I-465 on the northwest side of Marion, just east of Eagle Creek Park. I am going to have four aerial photos in this entry: 1941, 1956, 1962 and 1972. Also, small snippets of several topo maps are used. Strangely, the 1941 and 1956 are almost identical.

1941 MapIndy aerial photo of the area around the I-65/I-465 interchange on the northwest side of Marion County.
1956 MapIndy aerial photo of the area around the I-65/I-465 interchange on the northwest side of Marion County.
1961 USGS Topographic Map of the interchange between I-65, I-465, and future SR 100, now known as I-465.

The 1961 USGS Topo map shows the pending SR 100 connection. Bridges appear in the 1962 aerial, especially Lafayette Road over I-465. It should also be noted that on the USGS maps, the pending I-465 was also marked SR 100. Also, what is now I-65 fed directly into Lafayette Road at this point. This made sense, since I-65 was the replacement, between Indianapolis and Labanon, of US 52…which followed Lafayette Road in this area.

The next photo is from 1962. The missing section in the picture had not changed much, if at all, from the 1956. The Dandy Trail did not cross Eagle Creek at a right angle to the creek. It had been replaced by a bridge on 56th Street. And the reservoir still hasn’t been built. Both interstates, I-65 going straight through the area, and I-465 veering off to the south, catch the eastern edge of the park like area west of Lafayette Road north of 62nd Street. That park like area is listed on the 1953 USGS topographic map as “Eagle Creek Forest.”

1953 USGS Topographic Map of Eagle Creek Forest.

It should be noted that 62nd Street was completely orphaned west of the interstate when it was built. Reed Road, which at the time before the building of the reservoir and the park ended at 62nd Street, was the access to the orphaned section west of the interstate.

The state had already made plans to make the complete I-465 loop, including between 56th Street north to the north leg. However, it never did get federal approval. If it was going to be built, the state would have to build it not as the interstate, but as a state road. Hence it was decided that the road that I-465 was replacing, SR 100, would be the designation for that section.

1962 MapIndy aerial photo of the area around the I-65/I-465 interchange on the northwest side of Marion County.

The topo map of 1967 (1969 edition) shows the completion of Eagle Creek Reservoir and Park. It shows the area that had been the Dandy Trail Bridge over Eagle Creek. I have included two snippets of that map. The first is the I-465/I-65 interchange, with the proposed SR 100 connection. The Second shows the 56th Street causeway over the reservoir.

1969 USGS Topographic Map of the I-65/I-465/Proposed SR 100 interchange.
1969 USGS Topographic Map of the 56th Street Causeway over Eagle Creek Reservoir.

By the time that the 1972 photo was taken, the Eagle Creek Reservoir and Park was in place. Reed Road, which allowed access to the park area with the circular road, was still in place, but as I recall it had been closed to traffic on the 56th Street end. The Dandy Trail bridge had been replaced with the 56th Street Causeway, mainly because the old road was under water at that point.

The major change, relating to the subject at hand, was the completion and connection of the section of I-465 north of I-65 heading off towards the north leg of the bypass route. That section was built not as part of I-465, but as SR 100. It wouldn’t stay SR 100 long, as the Feds allowed it to become I-465…as long as the state continued to pay 50% of the building cost as opposed to the normal 10%. So, yes, that section of I-465 was a state choice…the Feds approved it after construction was started. This would cut even more of 62nd Street, and High School Road, out of the city landscape. The curve, connecting Lafayette Road to 62nd Street heading east, had already cut the corner of 62nd Street and High School Road off from connecting with anything other than Lafayette Road to the west.

1972 MapIndy aerial photo of the area around the I-65/I-465 interchange on the northwest side of Marion County.

It hasn’t change much in that area since 1972. There are some rumblings of changing the interchange to make it more friendly to interstate-to-interstate transfer. But nothing has come of it.

I-465 and I-70, Marion County East Side, A Pictorial History

Today, I want to take a look at the interchange between Interstates 70 and 465 on the east side of Marion County…in pictorial form. This history will cover from 1962 to 1993, with what aerial photographs are available from MapIndy, the official mapping application of Indianapolis/Marion County. It will also cover the interchange between Interstate 70 and Shadeland Avenue, which was SR 100 before, and for some time after, the building of its replacement, I-465.

1962
1972
1978
1979
1986
1993

Two of the constrictions at the location of this interchange were both 21st Street and Franklin Road. Franklin Road had been in place since it was created as the Noblesville-Franklin State Road early in the state’s history. As you can tell from the photos, the routing of Franklin Road was changed between 21st Street and around 25th Street. The original routing of the road is still in place, but contains two dead end sections at the interstate.

21st Street has been around for a whole lot of years, as well. Maps show that it was added to the county sometime between 1870 and 1889. In 1889, there was a toll house for the Pleasant Run Pike on the northwest corner of 21st Street and Shadeland Avenue. From what I can tell, the only part of the road that was a toll road was from Arlington Avenue to Mitthoeffer Road. Today, 21st Street can be followed from Massachusetts Avenue at the Bee Line (Big Four – Conrail – CSX) Railroad to a point just northwest of Charlottesville.

The ramp from I-70 West to I-465 South was under construction in 1978, and would be completed in 1979. Prior to this, that traffic movement was handled by a loop ramp, as the interchange was originally built as a 3/4 cloverleaf. By 1993, the current collector/distributor system connecting Shadeland Avenue to both I-70 and I-465 was completed.

The ramps to Shadeland Avenue have always been a very tight fit into the area allowed.

1959 – Interstate Contract Bids

When the interstate system started being built in Indiana in the late 1950’s and early 1960’s, contracts for building those roads started flying fast and furious. The interstate system came into being in 1956…and the first contracts were finally let in 1959. The Indianapolis News of 29 May 1959 reported all of the contracts that were let to that point.

First four miles of Interstate 465: “Low bid for construction of the first 4 miles of Interstate 465, the new belt highway to encircle Indianapolis, has been submitted by an Evanston (Ill.) firm. The construction contract also will include the building of 1 1/3 miles of Interstate 65 – the Indianapolis-to-Chicago expressway – northwest of Indianapolis.”

One of the things that keeps coming up when it comes to the interstates, their designations and their contracts is the actual name for I-465. Legally, that’s what it was, Interstate 465. However, for many years, until the interstate was done, or even beyond, the news media would not only refer to it as Interstate 465, but as the New State Road 100. A lot of people at the time simply saw it as a replacement for SR 100, which it was. This was also brought on by the fact that the original contracts from the state had project numbers for both roads.

This contract covered I-465 from a point north of US 136 to West 62nd Street. It would run west of High School Road through the area. The section of Interstate 65 included in this contract would run “parallel with and west of U.S. 52, from just northwest of West 65th to just southeast of High School Road.” The bid for this contract was $2,257,679.81.

The same company won the $1,705,758.49 bid to construct Interstate 74 from SR 267 in Brownsburg to just east of the Hendricks-Marion County Line. This 4.5 mile section of what the News referred to as the “Indianapolis to central Illinois expressway” would be built north of US 136.

As is typical of the way Indiana bids contracts for road projects, bridges and roads are bid separately. The above contracts did not allow for bridges…just the approaches. Bridges would be bid usually earlier than the road.

The first new Ohio River bridge linking Indiana and Kentucky in 30 years was let on a bid of $994,979.58 to Roy Ryan & Sons of Evansville. “The bridge will be double-decked, with three lanes of one way traffic on one level and three lanes of one way traffic on the other level.”

Three bridges were let on the Interstate 74 project mentioned above. Ruckman & Hansen, Inc., of Fort Wayne, won two of them. $187,129 for the bridge over Big White Lick Creek west of SR 267, and $219,553 for the bridge over SR 267. Carl M. Geupel Construction Company bid $218,712 to build a county road bridge over Interstate 74, 1.2 miles southeast of SR 267.

These were among the first contracts to be let on the new Interstate highway system in Indiana. Many more would come.

National Road Through Richmond

When the National Road was surveyed through Indiana, it had the distinct honor of being one of the straightest roads in the state…another being the Michigan Road. This was on purpose. Most roads through the state were built around whatever was in the way. Very few roads were built for getting from point a to point b in the quickest way possible. That was left to the state to buy the property necessary to do that.

One notable exception is through Richmond.

The area around Richmond started being settled around 1806. By the time the National Road surveyors got there in the early 1830’s, the town had already been established. And in the way of the nearly straight as a board road coming from the Ohio capital of Columbus. So when the road got to Richmond, it made sense to run it straight down Main Street. And that’s what happened.

However, on the west bank of the Whitewater River, upon which Richmond sits, the continuation of the straight line from Ohio would be continued. This would mean that the road would actually start again south of its location through Richmond. One block south, as a matter of fact. This led to the layout of Richmond, and the road, as shown in the following 1840 map snippet.

On this map, it is labeled Cumberland Road.

As you can see, the Cumberland Road is opposite Walnut Street on the west side of the Whitewater River. That would be South A Street today. The name change of the streets would occur sometime before 1893, as shown in the 1893 snippet below.

The National Road bridge over the Whitewater River would be built in the location shown on the first two snippets in 1832. The same bridge served residents of Wayne County and travelers on the National Road for 65 years. News reports across the state were reporting that deconstruction of the bridge would occur in August 1897. (Source: Muncie Evening Press, 13 August 1897) It was reported in the source newspaper that “the work of removing the old National road bridge at Richmond, Ind., will begin next week.”

The slight variations in the location of the bridge between the 1840 and 1893 maps are just that, slight variations and could be attributed to slight errors. A measurement here or there could change the map by a few feet…which looks like the case here. Another map, this time from 1853, shows the same area, more like the 1840 map than the 1893 variety.

The original structure was a very large affair…at least for that time. It was easily as large as the National Road bridge at Indianapolis. The Richmond Palladium-Item of 21 October 1962 did an article on a painter from Centerville that had done two paintings of the old bridge. A picture from the article is below.

Another view drawn of the bridge was published in 1911 in Century Magazine. It would accompany an article about the old bridge written by a Richmond native. That drawing is shown to the left.

In 1916, it was reported in the Cambridge City Tribune of 3 February 1916, that “the total cost of the construction of the temporary bridge across Whitewater at the location of the old National road bridge at Richmond was $4,895, of which the county, city and traction company each pay one-third, or $1,798.” I can find no news story about why a temporary crossing of the river was necessary.

The original route, more or less, of the National Road through Richmond would become Main Market Road 3 in 1917. That designation would be changed to State Road 3 in 1919. The slight difference would be on the west side of the river, where the state road followed First Street, not the river, to travel between Main Street and National Road. By this time, a third bridge over the Whitewater River was serving as the facility to cross that wide gorge. On 1 October 1926, SR 3 would be forever changed to US 40.

1962 USGS Topo map of US 40 through Richmond.

In 1998, INDOT decided to build a new bridge across the river, and reroute the old National Road/US 40 through the city of Richmond. This would put the road on its current path through the city, leaving Main Street out of the mix, at least west of 11th Street, as the major thoroughfare for the first time in almost 200 years. The city of Richmond took over the then abandoned route of US 40, creating a more plaza like environment along the historic street.

The new US 40 bridge that was completed in 2000 was advertised as the fourth bridge to serve as the National Road crossing of the Whitewater. I suppose, in a way, this is true. However, the historic crossing was closer to Main Street, which still has a bridge facility across the wide gorge. Not that I have heard arguments over the issue, it is one that road geeks and historians (or, in my case, both) will probably be discussing for years to come.

Vincennes: The Lincoln Memorial Bridge

Few people in American history hold a place as high as Abraham Lincoln. The Kentucky native that became the 16th President of the United States, also spent time living in Indiana before moving on to Illinois, where he would become famous throughout the nation. It was decided that a bridge, supposedly marking the spot where Lincoln crossed into Illinois, would be built to connect Indiana and Illinois. It became the Lincoln Memorial Bridge.

The George Rogers Clark Memorial was soon to be constructed in Vincennes. As part of that memorial, a celebration on 3 September 1933 to dedicate a new bridge at Vincennes connecting Indiana and Illinois were scheduled. The date chosen for the dedication of the bridge was the 150th anniversary of the signing of the Treaty of Paris, bringing an end to the War for Independence and the creation of the United States of America as a separate country.

The Abraham Lincoln (George Rogers Clark) Memorial Bridge as shown in the Indianapolis News of 28 April 1934.

The bridge, when it was built, would carry US 50 across the Wabash from Vincennes, Indiana, to Lawrence County, Illinois. It would become a major link in that road for several decades. It would be a replacement of a bridge that spanned the Wabash from Main Street in Vincennes for many years.

The high approaches on the Indiana side were due to requirements by the War Department. The Munster, Indiana, Times of 17 July 1931 states that “rigid war department requirements forced the engineers to give the 1,850-foot bridge a clearance of 50 feet above the normal water level on the theory that some time navigation might be resumed in the Wabash.”

At one point, the plan of the city of Vincennes, and Knox County, was to build a boulevard between the George Rogers Clark Memorial and the Wabash River for the rerouting of US 41 along the new route. I am not sure if it was part of the plan, but Culbertson Boulevard runs from Main Street north to Hart Street between the railroad and the river. The US 41 idea never materialized.

In 1936, the bridge, as well as US 50, would be closed for one day. Sunday, 14 June 1936, would see the closing of US 50 in both Indiana and Illinois as the George Rogers Clark Memorial was dedicated at Vincennes. For four and half hours, detours of over 40 miles were in place as festivities were held to celebrate the GRC Historic Park dedication. Chief among those that would be on site would be President Franklin Delano Roosevelt.

The Abraham Lincoln Memorial Bridge still stands today, almost 90 years after the concrete structure was built. Yes, US 50 has been rerouted around Vincennes. The bridge now serves as Indiana State Road 441. And, according to Google Maps, the same road number in Illinois, although on the ground, there are no such markers in place that I have ever seen.

Indianapolis and Requested Changes to the Interstates

The construction of the interstates in and around Indianapolis were always contentious. Whether it be a direct route to the northeast side, or the routing of Interstate 65 from downtown, controversy was never a stranger to the entire process. Things were desired, things were shot down. Today, I want to focus on some requests from the Metropolitan Plan Commission to the State Highway Commission when it came to the designs of both I-465 on the east side and I-65 on the south side. These requests were publicized in July 1968.

The reason that the Metropolitan Plan Commission ever was involved in the first place was a then new Federal regulation designating the group as the review agency for the entire region. The MPC was given review powers over any project that used Federal funds in any way.

The first project that they wanted to change involved I-465 from 56th Street to White River. The major recommendation for this project is that land be acquired between the interstate and Shadeland Avenue, then SR 100, for landscaping between the two. The MPC also made the request that SR 100 between Fort Benjamin Harrison and Castleton be widened, eventually.

Two other recommendations for I-465 were purchase of more right of way in the area of Allisonville Road and 82nd Street, and the removal of the planned 75th Street bridge. The first would allow improvements to the intersection of Allisonville and 82nd…something that is always needed, especially after improvements are made. The second would have eliminated any crossing of the interstate between 82nd Street, which at the time was SR 100, and 71st Street.

The major recommendations were made to the south side on Interstate 65, however. Those recommendations would lead to a very different scenario for those traveling I-65 between Thompson Road and Whiteland Road.

The first recommendation involved Stop 8 Road, now called Edgewood Avenue. The original plan involved Stop 8 Road crossing over the interstate, as it does to this day. The MPC recommended that plan be scrapped, and a full interchange be put in at Stop 8 Road. The building of the current overpass at Edgewood required the demolition of two homes, and the building of an access road to several others. As shown in the 1962 MapIndy aerial photograph below, it would have required much more ROW acquisition.

The second recommendation was to change the planned interchange at Southport Road to just a grade separation. That’s right. The busy intersection of Southport Road and Emerson Avenue would have not involved an interstate interchange as it does today. I am unsure why such a recommendation would have been made. Below is an aerial picture of the area in 1962.

Next, the Metropolitan Plan Commission recommended a change to the width of the Stop 11 bridge clearance, making it wider. This would allow a wider roadway under Stop 11 Road. They also recommended that it be considered for conversion to a full interchange at a later point.

The last two recommendations would allow for a wider roadway for the interstate, and room for expansion later. The two bridges that would be involved were the Emerson Avenue bridge and the County Line Road bridge. The ROW under these two structures, it was recommended, should be wider.

In the end, most of the recommendations involving interchanges were shot down in the end. Southport Road became the access point to I-65. You could still cross the interstates at Edgewood Avenue, Stop 11 Road, and 75th Street. The bridges at Emerson and County Line were made wider and higher for future expansion.

Cambridge City, 1870

Today, I want to look at another historic map available from the Indiana State Library Online. This map is, as the subject states, of Cambridge City in 1870. It is available here: http://cdm16066.contentdm.oclc.org/cdm/singleitem/collection/p15078coll8/id/2896/rec/31

Cambridge City…for the longest time it was essentially a cross roads town, but not with the number of mud paths to the city. There was a state road to the north of town…but I have been unable to find where it went. Today, that state road is Delaware Street. But the major contributors to the transportation success of Cambridge City would be the National Road and the White Water Canal.

Later, the town was crossed by three different railroad companies, which would, in the end become the New York Central (Big Four), the Nickle Plate and the Pennsylvania. Of which only one exists today.

Cambridge City today shows its history, although a majority of the traffic passes a couple of miles north along Interstate 70.

I plan on just letting the map do most of the talking for me today. I really hope you find it as interesting as I do.

SR 67 in Northeast Marion County

When the Great Renumbering occurred on 1 October 1926, the number 67 was assigned to the Pendleton Pike connecting Indianapolis to Pendleton, through Lawrence and Oaklandon. This would be part of the greater State Road 67 stretching from Vincennes to Muncie…and later to the Ohio State Line. But the route in Indianapolis, and northeast Marion County, would carry the road along Massachusetts Avenue to the city limits, where the name would change to Pendleton Pike.

One of the first changes would involve the adding of US 36 to the same path. Although US 36 is higher in priority, most of the businesses along the old route kept the “67” as part of their names if it included it. As a matter of fact, I find it hard to believe that even today, there are no businesses along that road that include the number “36,” at least as I can recall. But there is a Motel 6t7…with a US route shield shaped sign…as shown to the left.

Changes were being planned for the road in 1933, when it was decided that SR 67 (and as a result, US 36) would be three laned from Indianapolis to Anderson. This would result in a change in the historic path of the Pendleton Pike from northeast of the then town of Lawrence to just south of Pendleton. In Oaklandon, for instance, the old SR 67 followed the current path of Pendleton Pike to what is now Oaklandon Road (formerly Germantown Road, named after the village that is now currently under water in Geist Reservoir at the Marion-Hamilton County line). The road then went north on Germantown (Oaklandon) to Broadway, turning northeast on that street. The old connection between Broadway (old SR 67) and the current Pendleton Pike (US 36/SR 67) still can be seen northeast of Oaklandon.

In 1935, the State Highway Commission decided that the number of miles inside the City of Indianapolis that it had to maintain would best be served if the number was lower. At the time, most of the northern city limit was at 38th Street, the dividing line between the middle tier and northern tier of townships. Where the Pendleton Pike now ends, at 38th Street west of Shadeland, was where the city ended at that point in history.

A bridge contract was let to Edward F. Smith to build a five span, 217 foot long bridge over the Big Four Railroad along 38th Street west of the intersection with SR 67, which was Massachusetts Avenue/Pendleton Pike. The bridge, in 1935, cost $143,825.01. The Indianapolis News of 25 May 1935 states that “Thirty-eighth street, with this and other contemplated improvements, is to become State Road 67. Construction will start in a few days and is scheduled to be completed by November 15.” Plans to move SR 67 to the 38th Street corridor were mentioned in newspapers as far back as June 1933, when plans for a new Fall Creek bridge on 38th Street, near the State Fair Grounds, were in the works.

While construction was going on between Indianapolis and Anderson in 1935, the official detour route had changed in late June. The original detour involved taking US 40 to Greenfield, then north on SR 9 to Pendleton. The new official detour recommended using SR 13 (became SR 37, now Allisonville Road) to SR 32 in Noblesville, then SR 32 to Anderson. This was recommended over the SR 38 route to Pendleton since SR 32 was a hard surface road, and large section of the newly added SR 38 were still gravel.

By 1937, SR 67 would find itself skirting Indianapolis, at least on the north side, along 38th Street. The old SR 67, Massachusetts Avenue, would find itself labelled SR 367. The three lane project between Indianapolis and Anderson would be completed, and Oaklandon would find itself bypassed by one of the two transportation facilities that made it possible. Now, most of what is left of SR 67 on the northeast side of Marion County (Pendleton Pike from I-465 east) is at least five lanes wide…but quite a bit of it is seven.