West Marion County and I-465

This image has an empty alt attribute; its file name is images.jpg

The first part of the new beltway (almost) around Indianapolis started on the westside of Marion County. As mentioned in other articles, the original plan was to start Interstate 465 at Interstate 65 on the northwest side, with the replacement for State Road 100 (which I-465 officially was) heading south from there to circle around the county from there. Interchanges were planned at I-65, I-74/US 136, 10th Street, US 36 (Rockville Road), US 40 (Washington Street), Weir Cook Municipal Airport (Airport Expressway), Interstate 70, and SR 67 (Kentucky Avenue). According to USGS topo maps, like that included below, show that there was a stub ramp connecting I-465 to 62nd Street, although the ramp connecting to 62nd Street was listed as still proposed six years later.

1962 USGS topographic map showing the original interchange connection Interstate 65 and Interstate 465.

Construction started along the corridor in 1959. The Indianapolis News ran a series of pictures showing the plans set out by the State Highway Department. If you noticed the list of interchanges above, there were no plans for 56th Street or 38th Street to have ways to access 465. Bridges were to be built over 465 at 56th, 46th, 38th, 34th, and 21st Streets. (21st Street was a very special, and contentious, situation. I covered it in the article: “Building I-465 at West 21st Street. [8 May 2020]”)

Indianapolis News, 14 December 1959, showing the Indiana State Highway Department’s plans for the new Interstate 465 (also still called State Road 100 at the time) at the northern terminus of the highway.

The plans for Interstate 65 at that point were to continue to have it replace US 52 (Lafayette Road). The US 52 bypass at Lebanon was made part of the new I-65. The temporary plan was to connect I-65 just southeast of I-465 directly to US 52 until construction could continue. Then I-65 would also be US 52 from that point to northwest of Lebanon. I mention this only because the loop around Indianapolis was, apparently, easier to get approved than trying to run I-65 through town. (And since it would take another 16 years to complete, even to the point that an addition was planned to I-465 and completed before I-65 through Marion County says it all.)

It wouldn’t take long after the original plans for the interstate were laid down that changes were made. The non-planned 38th Street interchange was added to the deal. It was to be a partial cloverleaf interchange connecting to 38th Street at that point. Marion County had decided to build 38th Street from Lafayette Road east to the new White River bridge to be built by the city. At that point in history, 38th Street was a county road with nothing resembling the connections it has today as a major west side thoroughfare.

Indianapolis News, 11 December 1959, showing the future connection to 38th Street from I-465. This ramp would be built much later, when 38th Street was finally connected as a thoroughfare across Marion County.

The next interchange south of the “gonna be built someday” 38th Street was the connection to another interstate highway, Interstate 74. The plans shown in the Indianapolis News differ slightly from what was actually built. US 136 (Crawfordsville Road) is directly connected to the east end of the proposed interstate connection. This would change. It looks like the proposed interchange was moved slightly north, and Crawfordsville Road west of High School Road was turned north to connect to High School Road. This would be where US 136 would ultimately officially end.

Indianapolis News, 10 December 1959, showing the proposed connection between interstates 74 and 465. The original plan, and this was carried out, is that Interstate 74 would “travel over,” ISHD/INDOT term for multiplex, with I-465 from northwest to southeast Marion County.
1953 Topo map showing the intersection of West 10th Street and High School Road.

The next section did change, at least at one interchange, quite a bit. But before I describe that, let’s talk about the placement of I-465 from Vermont Street north to about where 16th Street would be, if it continued to High School/Girls School Road. The new interstate was planned, in that section, to be built directly over High School Road. This is not really a stretch, since High School Road, from Washington Street south to the Airport, was the original State Road 100. And I-465 was, for all intents and purposes, State Road 100 according to ISHD.

I have written a detailed history of SR 100 (SR 100: How did it come to be? [9 March 2019]) and an article about how, at one point, the connection between SR 100 on BOTH sides of Marion County were to have cloverleaf interchanges (“The Cloverleaf Interchanges at US 40 and SR 100” [20 November 2019]). If SR 100 had been completed on the west side, like it was on the north and east sides, I have no doubt that it would have followed High School Road north, probably, ultimately, to 86th Street, which was SR 100 along the northwest side.

The change in interchanges happened at 10th Street. The original plan was for a full cloverleaf interchange at that intersection. This would have pushed the eastbound 10th Street to southbound 465 ramp back closer to Glen Arm Road, where High School Road was rerouted to miss the interchange. What was ultimately built was a jumbled three-quarter cloverleaf with a flyover from westbound 10th to southbound 465.

In the end, High School Road was basically built over by 465 from Vermont to 10th Streets. 10th Street is a survey correction line, so High School actually moves slightly to the east at that point, as shown in the topo map to the left. For more information about survey lines, check out “Survey Lines and County Roads. (29 March 2019)”

Indianapolis News, 9 December 1959, showing the Indiana State Highway Department plans for I-465 from just south of the New York Central railroad tracks to just north of the Baltimore & Ohio Railroad tracks, including what was to originally be full cloverleaf interchanges at 10th Street and Rockville Road.
1953 USGS topo map of the area of Washington Street and High School Road. The area marked “Ben Davis” would be the location of the new cloverleaf interchange between US 40 and I-465.

From the looks of aerial photos in 1959 as shown in the Indianapolis News, the interchange at Washington Street was going to be very destructive. (Keep in mind that as of the writing of this article, MapIndy, my go to source for historic aerial photos of Marion County no longer offers that service. Maps are available, but the aerial photos are gone.) In addition to the shunting of Morris Street (a survey line and historic route of its own accord), most of where the interchange between US 40 and I-465 was basically what had been the town of Ben Davis.

Another thing would have to happen before this interchange would be built. It was determined, and reported, in July 1959 that an improvement of West Washington Street would have to occur before the interstate reached that point. US 40 was to be widened in the area. The work on Washington Street, however, would have to wait until sewer work in the area was completed…probably in 1961. Plans to widen Washington Street from 40 feet to 68 feet wide, with a four foot median and an eight parking lane on each side, were decided upon. Very little of that plan exists today…and if it does, it’s hard to find.

Indianapolis News, 8 December 1959, showing the proposed area of US 40 and Interstate 465.

The last area covered by the Indianapolis News in the series of articles (actually, it was the first since the editor staff decided to post them south to north, even though the interstate was built north to south!) shows the area of I-465 near Weir Cook Municipal Airport. The one change that I can see is what would become Airport Expressway (check out “Indianapolis’ Raymond Street Expressway” [4 February 2020] for the history of what started out as the Bradbury Expressway) was proposed to connect to the airport heading slightly north of due west, just above Southern Avenue. This section of the (now) Sam Jones Expressway is due east-west at the point it connects to Interstate 465. For a history of what is now Indianapolis International Airport, check out “Indianapolis Municipal Airport.” (20 August 2019)

Indianapolis News, 7 December 1959. This newspaper snippet shows the area of proposed I-465 near the (then) Weir Cook Municipal Airport (now Indianapolis International).

That covers the first of the construction of the State Road 100 replacement. I want to share this one last snippet from the Indianapolis News of 19 October 1960. It shows the construction of I-465/I-65/US 52 at 62nd Street…or the original northern end of Interstate 465.

Indianapolis News, 19 October 1960, showing the original northern end of Interstate 465.

Original SR 31 and the Pike’s Peak Ocean-To-Ocean Highway

Just a short post to show how state roads have changed.

I have covered Auto Trails and the original state road numbers several times over the past nearly two years. I had done a post about the rerouting of the Pike’s Peak Ocean-To-Ocean Highway through Indiana. But the original route, as covered by fellow blogger (and ITH Facebook Group co-admin) Jim Grey, traveled across the western part of the state using the US 36 corridor. (The latest is “US 36 and the Pikes Peak Ocean-to-Ocean Highway in Danville, Indiana,” among others) I’d like to say it followed the current US 36, but it’s been moved several times over the years.

As I had mentioned in other posts along the way, many of the roads that were added originally to the state highway system were part of the Auto Trails systems that crossed the United States. When the Pike’s Peak road was taken into the state system, it was given the designation “State Road 31.” Well, sort of.

OSR 31 started in the west at OSR 10, across the Wabash River west of Montezuma. From there, it went through Montezuma, Rockville, and Bainbridge to Danville. From Danville, the PPOO rumbled across Hendricks and Marion Counties along what is now Rockville Road (and Rockville Avenue – because Rockville Road didn’t connect to Washington Street directly until later). The original SR 31, however, connected to the National Road (then Original State Road 3) at a completely different location.

Strangely, the route of the original SR 31 is now not part of the state highway system. Current SR 39 leaves Danville via Cross Street south towards Martinsville. Original State Road 31 turned south from Main Street on Jefferson Street. Jefferson Street turns into Blake Street, then Cartersburg Road. The state road connected to OSR 3 southeast of Cartersburg.

The drive from Danville to Cartersburg is quite a nice one.

With the Great Renumbering in October 1926, original state road 31 became US 36. Again, sort of. The section from Danville to Cartersburg was removed from the highway system at that time. US 36 continued on into Marion County, as shown in the article “Road Trip 1926: US 36.” Just like the original eastern end of OSR 31, the original eastern end of US 36 is now gone, ending at a parking lot.

I also covered a reroute that was put in place along US 36, after the Great Renumbering, at Bainbridge.

Indianapolis’ West Washington Street

It goes without saying that Washington Street in Indianapolis has always been an important facility. Since 1821, when the town of Indianapolis was platted, Washington Street has had a prominent role in the expansion of the city. When the National Road came to Indiana, it followed that same town path through the fledging Hoosier Capital. But today, I am going to fast forward into the 20th century to discuss how it became a major concrete ribbon through town, at least on the westside of Indianapolis.

No matter how important Washington Street was to the city, it had, at least outside of downtown, been not much more than what we would call two lanes wide for the first half of its life. With the coming of the automobile, these old narrow cow paths were going to have to be put on a path to make them usable by more people at a time. Way back in the middle 19th century there were discussions, heated at times, about the width of sidewalks on the street, since only the center was covered with gravel for traveling.

The Indiana State Highway Commission decided that the National Road would be part of the state highway system. This, one would think, would automatically include West Washington Street. It didn’t. It just so happened that Washington Street made a direct connection between SR 3 (US 40) both east and west of the city. But Washington Street was still a city street.

In 1937, there was some talk about the Board of Works and Sanitation of the City of Indianapolis widening West Washington Street from White River west to the city limits…at that time near Tibbs Avenue. That plan was in the works, but there was one project approved for the area: widening of Washington Street between Traub and Tremont Avenues, in front of George Washington High School.

The Indianapolis News of 16 January 1937 ran a full page story about the history and pending expansion of West Washington Street. That article mentioned that the widening of the street in front of Washington High School would allow for the creation of safety islands for students trying to cross the busy thoroughfare. West of the city limits, the old National Road, by that time US 40, was already four lanes wide. Through the city itself was a bottle neck.

But the plan never got off the ground. That same year, the General Assembly passed legislation that would remove Washington Street from city control and give it to the State Highway Commission. This would make any widening of the road a state project, no longer a city problem. While the city could ask for something to be done, the state would be the ones to do it. And the wheels of progress sometime work very slowly at the state level.

Fast forward a decade, or so. “The State Highway Commission will receive a recommendation for the rebuilding of 2.1 miles of West Washington Street between White River and Eagle Creek.” So states the Indianapolis News of 20 May 1948. Three months, at that time, had been spent on surveys to figure out exactly how to widening the old National Road.

The end point to the west is important to note here. Around 1937, a new bridge was built by the State Highway Commission to carry US 40 and US 36 across Eagle Creek. This new bridge would be built north of the old structure, and would also entail moving the intersection of Washington Street and Rockville Road (US 40 and US 36 respectively).

MapIndy aerial photograph of the intersection of Washington Street and Rockville Road, 1937.

The 1948 project would include widening West Washington Street to 60 feet wide. That included four 11 foot wide travel lanes, two in each direction, and two eight foot parking strips (one on each side). The then current road surface, consisting of brick and blacktop, would be completely removed and replaced with concrete. New sidewalks were also part of the project.

There was to be a one block gap in the project, however, due to a planning and construction question. The plans included an underpass, allowing Washington Street to go under the Indianapolis Belt Railway at Neal Street. State Engineer of Road Design, William H. Behrens, recommended that such an underpass be postponed until construction costs could come down. “He said he favors a gap of 1 block in the new construction at this point.”

A spokesman for the Indianapolis Railways stated that when the construction was underway, the company would remove its unused streetcar tracks from Washington Street from the car barns near White River (where the Indianapolis Zoo is now) to a point 100 feet west of Tibbs Avenue.

The News pointed out that “the State Highway Commission has charge of the project because Washington Street is part of Roads 40 and 36. It is also part of the old National Road.”

Indianapolis Star, 19 August 1951.

The next reference I have found to the expansion of West Washington Street, I will let speak for itself. It is the news story from the Indianapolis Star of 19 August 1951 shown above. Apparently, this was the second annual party to celebrate the completion of the 1948 project.

Indianapolis and the Original ISHC State Road System

I have posted much about the creation of the Indiana State Highway Commission. As of the posting of this article, the age of the Commission is either 103 or 101 years old. The original ISHC was established in 1917…but met with a lot of problems. It was finally nailed down in 1919 and made permanent.

This also creates a dating problem when it comes to the state highways. The first five state highways, then known as Main Market Roads, were established in 1917 with the original ISHC. Two of those original Main Market Highways connected to Indianapolis. The original National Road had been given the number Main Market Road 3. The Range Line Road, connecting Indianapolis to Peru, and through further connections, to South Bend, was given the Main Market Road 1 label.

When it was finally established, the ISHC changed the name of the Main Market Road to State Road, in keeping with other states surrounding Indiana. The markers used along the roads, painted onto utility poles like the old Auto Trail markers were, resembled the image to the left…the state shape with the words “STATE ROAD” and the route number. In this case, as of 1920, State Road 2 was the original route of the Lincoln Highway through northern Indiana.

The state highway system was designed to, eventually, connect every county seat and town of over 5,000 population, to each other. Indianapolis, as the state capital and the largest city in the state, would have connections aiming in every direction. Most of those roads marked with the original numbers would still be state roads into the 1970s and early 1980s, before the Indiana Department of Highways started removing state roads inside the Interstate 465 loop…and INDOT finishing the job on 1 July 1999. These road were removed for state statutory limitation reasons, and I have discussed that in a previous blog entry. So I won’t do it here.

The original state road numbers that came to Indiana varied greatly, as did their directions. There were no set rules when it came to state road numbers. They were assigned as they came…and stayed that way until the first renumbering of 1923, or the Great Renumbering of 1926.

Let’s look at the original state roads in Marion County, some of which actually did not reach Indianapolis itself.

State Road 1: As mentioned before, State Road 1 was originally called Main Market Highway 1. North of Indianapolis, it followed the Range Line Road, a local Auto Trail, through Carmel, Westfield, to Kokomo and points north. The route north followed Meridian Street north to Westfield Boulevard, then Westfield Boulevard on out to Carmel and beyond. In Carmel, the old road is still called Range Line Road, and serves as the main north-south drag through the town, as it does in Westfield.

South of Indianapolis, State Road 1, like its Main Market Highway predecessor, followed the old Madison State Road out of the city to Southport, Greenwood, Franklin and Columbus. The original SR 1 route is still able to be driven through the south side of Indianapolis, with the exception of the section replaced in the 1950s by the Madison Avenue Expressway. But Old Madison Avenue exists, if you can find your way back there.

While the entirety of original State Road 1 became US 31 with the Great Renumbering, bypasses in Marion County were put in place very early. The northern section, through Broad Ripple, and Carmel was replaced as early as 1930. The southern section, including the Southport/Greenwood bypass, was put in place in the 1940s.

State Road 3: As mentioned above, Main Market Highway/State Road 3 followed the National Road through Marion County. One exception to this is the section of the 1830s National Road that crossed the White River downtown. That section of the old road was removed in 1904 with the demolition of the National Road covered bridge and its replacement with a new, and short lived, Washington Street bridge. With a couple of exceptions other than that (the Bridgeport straightening of the early 1930s, and the new Eagle Creek bridge built in the late 1930s), the old road was followed very accurately until the mid-1980s with the creation of White River State Park. The successor to original SR 3, US 40, was moved to make room for the park. Both US 40 and US 31 lost their designations on 1 July 1999 with the removal of those two routes inside the I-465 loop.

State Road 6: This old state road was a through route when it came to Marion County. From the north, it followed the route of the original Indianapolis-Lafayette State Road from Lebanon. After passing through downtown Indianapolis, it left the county using the original Michigan Road on its way to Shelbyville and Greensburg. The original State Road 6 followed the Michigan Road Auto Trail, not the Historic Michigan Road, meaning it still went to Madison, but it went by way of Versailles, which the historic road did not. With the Great Renumbering, the northern SR 6 became US 52, while the southern SR 6 became SR 29 – later to be renumbered again to US 421.

State Road 22: This road, as it was originally laid out, only lasted from 1920 to 1923. Out of Indianapolis, it followed the old Mooresville State Road through southwestern Marion County. It was designated the original route from Indianapolis to Martinsville, as described in this blog entry. This road will be discussed again a few paragraphs from now.

State Road 39: Another 1830s state road that was taken into the Indiana State Highway Commission’s custody in 1919. This road followed the old Brookville State Road from the National Road out of the county through New Palestine to Rushville and Brookville. The original end of that road, both the 1830s original and the 1919 state highway, is discussed here. The road would become, in October 1926, the other section of US 52 through Indianapolis. It would also eventually become the first state highway removed inside the I-465 loop in Marion County. And even then, it would be rerouted in the late 1990s to go the other way around the county.

That covers the 1919 highways. More would come to Marion County before 1923.

State Road 12: Originally, this road, north of Martinsville, was the old State Road 22 mentioned above. When a new SR 22 was created, the SR 12 number was continued from Martinsville to Indianapolis along the old Vincennes and Mooresville State Roads. This road, in October 1926, would become part of the new State Road 67.

State Road 15: While the southern route of the Michigan Road was State Road 6, the northern part, heading off to Logansport, was added later and given the number State Road 15. The entire route of the historic Michigan Road would never become a state highway, but major sections did…although late in the creation of the state highway system. With the Great Renumbering, this road became SR 29, and in 1951, redesignated, like its southern half, US 421.

State Road 22: Here we go again. State Road 22 was given to the route between Indianapolis and Paoli. In 1919, that included the route along the west bank of the White River from Martinsville to Indianapolis along the Mooresville Road. This was changed by 1923 to keep SR 22 on the east side of White River, where it followed the old Paoli State Road, and the Bluff Road, through Waverly to the south edge of downtown Indianapolis at Meridian and South Streets. This was one of the routes of the Dixie Highway through Indianapolis, and would later become part of SR 37 in 1926.

State Road 31: In 1920, when this road was originally created, it turned south to connect to the National Road west of Plainfield. It had followed the Rockville Road from Montezuma to Danville, then turned southeasterly to meet State Road 3. By 1923, the road was moved from what would later become part of what is now SR 39 to continuing on the Rockville Road into Marion County. State Road 31 would meet the National Road outside the city limits of Indianapolis at what is now the intersection of Holt Road and Washington Street. It would become US 36 before it was extended along the new section of what is now Rockville Road to the intersection at Eagle Creek with Washington Street.

State Road 37: One of two state road numbers that still served Indianapolis after the road numbers were changed in October 1926 (the other being State Road 31). The original State Road 37 left Marion County in a northeasterly direction on its way to Pendleton, Anderson and Muncie. Inside the city limits, the street name was Massachusetts Avenue. When it reached the city limits, the name of the road changed to Pendleton Pike. This still occurs today, with the name change at the old city limits at 38th Street. In October 1926, the number of this road would change to State Road 67.

There were two other major state roads in Marion County, but they weren’t part of the state highway system until after the Great Renumbering. One was the Crawfordsville State Road, part of the original Dixie Highway, connecting Indianapolis to Crawfordsville via Speedway, Clermont, Brownsburg, and half a dozen other towns. It would be added to the state highway system by 1929 as State Road 34. The number would change later to US 136.

The other road was the original Fort Wayne State Road, also known as the Noblesville State Road, but even more commonly called the Allisonville Road. It would be added to the state highway system in 1932 as State Road 13. Less than a decade later, its number would be changed to the more familiar State Road 37.

Rockville State Road, US 36, near Bainbridge

When the original state roads were built, the state of Indiana created a road that connected Indianapolis to Rockville, via Danville. That road, still known today as Rockville Road in Marion County, is almost as straight as any road can get in this state. However, there were places where straight just wasn’t possible. Such a place is in Putnam County.

It should be noted that there were two things at play when it came to the building of the original state roads. First, the construction was done to keep costs to a minimum. There was no need to cat a path through a hill when one could just go around it. Path of least resistance was the motto of the day. Second, as a general rule, the state didn’t tend to take people’s property to build a road that would just be turned over to the county after it was built. This is one of the reasons that a road connecting two towns in early Indiana didn’t always go directly between two points. While it isn’t as noticeable on maps today, a quick glance at older maps shows the curvy way someone got from point A to point B in the early days of the state.

The Rockville State Road was (mostly) built along a section line, meaning very little property would have to be taken to create it. Generally, property lines in Indiana tend to work along the survey lines. Survey line separate townships, ranges and sections. Most of the time, property was purchased in one section or another, usually not crossing the section line. But there were several places that the old road did have to venture off of the survey lines beaten path.

One was east of Danville. Main Street through the city was the original Rockville State Road. When a short bypass between Danville and Avon was built, the old road was kept in place, but turned slightly at both the western and eastern ends. The following Google Map snippet shows the old property lines when it came to the western (Danville) end of old Main Street/SR 31/US 36. Main Street turns southwest, while the old property lines turn due west to connect to Danville itself.

The other section was a much larger bypass built by the state in 1933. East of Bainbridge, the old state road took a dive to the south of the survey line…sometimes venturing almost a mile south of the line itself. The following map is from 1911, showing the postal routes that were followed at that time, and showing the old Rockville State road in its original alignment.

As shown on the map, going west to east, the old road started turning southeastward in Section 12, continuing further southeast in Section 7, and hitting its southern most point in Section 8. From there, it worked its way back northeastward until it reached the section line again in Section 10. This created a variance from the section line that was nearly four miles long.

Editor’s Note: As is typical of the original surveys, sections along the western edge of the range [sections 6, 7, 18, 19, 30 and 31] are smaller than one mile wide. The Range Line between those sections listed above, and sections 1, 12, 13, 24, 25 and 36 of the range west, is known as a correction line. This can be spotted throughout the state, not only by the less than one mile wide sections, but the occasional deviance from a straight line going west to east. In Marion County, Shelby Street and Franklin Road are those correction lines…and looking at the roads crossing them shows the correction. The survey line along the north edge of the map is the township line, separating survey townships 15 North and 16 North. Following that line to the east, it becomes part of the Danville State Road in eastern Hendricks County, 10th Street (the geographic center) through Marion County, and the numbering center of Hancock County. It is also a correction line in the surveys, so sometimes survey lines jog a bit when crossing it as well.

This section of the old road was very curvy, narrow, and did not lend itself well to the pending explosion of traffic that would be coming its way with the creation of the Auto Trails and, later, the State Highway System. When the Pike’s Peak Ocean to Ocean highway was created, it followed the old Rockville Road from Rockville to Indianapolis. Thus, it followed this curvy, winding line through Putnam County.

Things would change in 1933, when the Indiana State Highway Commission announced that construction would begin on US 36 from Danville to Bainbridge. This project would complete the straightening of the federal highway from west of Indianapolis to the Illinois-Indiana State Line. The Indianapolis Star of 1 April 1933 reported “a twenty-five mile detour from Danville to Bainbridge on United States Road 36 over pavement and dustless type road has been established to take care of traffic pending completion of new pavement between Danville and Bainbridge which will complete the project from Indianapolis to the Illinois state line.”

The above Google map snippet shows the exact same area as covered by the 1911 USPS map shown above. The route of US 36 through the area, shown in yellow, is the 1933 bypass built by the ISHC. The old road is still very narrow and winding, but still can be traveled to this day. The Indiana Official Highway map of 1933 shows the new road under construction, with the old road removed from the map. By the time the next official map was released for June 1934, the new road was completed and opened. The following is the 1936 survey map of Putnam County roads, including road width, constructing materials and bridge of the same area.

The new roadway included bridges marked as AS, AT, and AU on this map. The old road included CN, CM, CH, CG, and CK. (Note, they are marked on the map in lower case letters. I am using upper case to denote them since it is easier to read.) Both AS and AU were built 24 feet wide, while AT was built 20 feet wide. All three had a safe working load of 20 tons.

The old road’s bridges were a bit more complicated. CN was 12.7 feet high, 12.7 feet wide, and had a safe working load of three tons. CK was 16 feet wide and could handle 15 tons. CM was 19.5 feet wide, with a working limit of 20 tons. This would make it almost equal to the bridge that replaced it (AT), only being six inches narrower with the same work load limit. Both CG and CH were 20 feet wide with a 20 ton safe load limit.

The old road, according to the figures on the 1936 map, had a right-of-way 40 feet wide. The new US 36 through the area had a right-of-way of 60 feet in width. Most of the county roads in the area had a right-of-way narrower than the old Rockville State Road, usually less than 10 feet.

The other part of this realignment project was through Bainbridge itself. The old road traversed the town along Main Street. The new road bypassed Main Street to the north…by only one block. It still does to this day.

Jim Grey, on his old web site, covers the sections of the old road that connect to the current US 36 fairly well. That page is at: http://www.jimgrey.net/Roads/US36West/04_Bainbridge.htm. I think I have read somewhere that this website will be migrated over to his WordPress blog, “Down The Road.” If this is the case, get it while you can. And who knows, maybe after all the “stay at home” mess is over, I might make a trip out to this section of the old road to take some onsite surveys. (I would love to say take pictures…but my lack of photography skills is only surpassed by my complete lack of patience to take the time to make them good. Not gonna lie here, folks.)

Bicycling Marion County, 1900, Part 2

Today is part two of two of covering a map I found on the Indiana State Library website about bicycling in Marion County, and the routes that were available.

Bluff Road: The direct route to Martinsville, Bloomington and points south. It was named after the Bluffs of the White River at Waverly. It was one of the first trails to connect to the Hoosier Capitol, as a lot of settlers would start their journey into Marion County from Waverly.

Clifford Avenue Pike: The extension of 10th Street past the city limits. The bicycle route ended at what is now Arlington Avenue, which connected Clifford Avenue to National Road and Brookville Pike.

Flackville Pike: The town of Flackville was created near what is now 30th Street and Lafayette Road. The Pike leading to the town is an extension of Indianapolis’ 30th Street.

Madison Road: The Madison-Indianapolis State Road, which the later Madison & Indianapolis Railroad would closely follow. Today, Madison Road is now Madison Avenue.

Millers Pike: Today known as Millersville Road, since that is where the road ended. A connecting route back to the White River & Fall Creek Pike used what is now 56th Street.

Myers Pike: This road would, in later life, become Cold Spring Road, connecting the Lafayette Road to the Michigan Road on the west (north) side of the White River.

Pendleton Pike: The old (1830’s) state road to the Falls of Fall Creek, where the town of Pendleton was formed. The old road went through Oakland (now Oaklandon), instead of basically around it like it does now.

Rockville Pike: The original Indianapolis-Rockville State Road. Still called Rockville Road for most of its length today. The old road is hard to navigate at its original beginning, since it was removed when Holt Road was built north of Washington Street. Rockville Avenue is the old road.

Shelbyville Road: The original state road to the seat of Shelby County. Its importance dropped off after the building of the Michigan Road. Near the current intersection of Shelbyville Road and Stop 11 Road/Frye Road, a branch took riders to Acton. At Acton, a branch from the Michigan Road came from the north.

Spring Mills Pike: The original path of Spring Mill Road started at the city limits on Illinois Street, crossing the White River near where Kessler Boulevard does today. It then continued up what is now Spring Mill Road into Hamilton County.

Sugar Flats Pike: The continuation of Central Avenue outside the city limits up to the Central Canal towpath, then following what is now Westfield Boulevard through Nora and into Hamilton County. The bike path led, after leaving Marion County, to the downtown area of Carmel.

Three Notch Pike: What is now Meridian Street was, for around a century, known as the Three Notch Road. The bicycle route followed Meridian Street from the Bluff Road intersection down to the county line.

White River and Fall Creek Pike: Labeled on the map as the White River and Eagle Creek Pike, this old road turned bicycle route followed the continuation of Keystone Avenue past the city limits to its end at River Road. Keep in mind, what is now Keystone Avenue north of White River was built by the state as a replacement for SR 431, which used to use Westfield Boulevard.

Bicycling the National Road West from Indianapolis

Route map from the Indianapolis News, 11 April 1896, showing bicycling routes.

Today’s Bicycling Thursday I want to go back to the Indianapolis News of 11 April 1896, which covered routes west of Indianapolis, starting with the National Road. While the article mentions shorter routes that use other roads back to the city, I want to stick to what is now Washington Street.

The first part of the journey was pretty much straight forward: “starting from Meridian and Washington streets, the run is out Washington street, which is paved some distance west of White River.” Before this point, the crossing of the White River could be done using one of two bridges, with more information available at “Indianapolis: Washington Street & National Road Bridges.” “Beyond the pavement, to the point where the National Road proper begins, the street is badly cut up.” This would be the section from roughly the Belt Railway to Mount Jackson, mentioned later. It was also mentioned that, while the road was in bad shape, the “going is good in the center of the car track.” Keep in mind that the “car track” mentioned here is that of the street cars.

1889 map of Mount Jackson and Haughville along Washington St.

“The National road starts from Mount Jackson, three miles out, and runs off a little southwest.” The town of Mount Jackson stretched from what is now Belmont to Tibbs Avenues, south of Washington Street. (Haughville proper was along the same stretch, north of Washington Street.) At what is now Warman, the “Indiana Insane Hospital” property was located. This property would be later named Central State Hospital.

At the edge of the hospital property, “a dirt road running northwest, skirting Haughville and crossing the Osterman (10 Street from White River to the Danville State Road), Crawfordsville and Lafayette roads.” This is now Tibbs Avenue.

1889 map of the National Road from the Eagle Creek crossing west, also showing the original connection of the National and Rockville Roads.

After passing the hospital, the old road passes over Eagle Creek “on a good iron bridge, the approaches to which are easy.” It then crosses the Big Four railway, which at the time was an at-grade crossing. The road then turns more to the southwest. Here “there has been a liberal supply of fresh gravel distributed over the road for about one mile, but there is a hard path at the side.” Also, there are two dirt roads branching from the main road in this section. One goes to Maywood, which is now Tibbs Avenue south of Washington Street. The other is between Tibbs and the place where the original Rockville Road turned northwest from the National Road (that intersection is now where Holt Road meets Washington Street).

About a mile from Rockville Road, the old road crosses a toll road that is a continuation of Morris Street from Indianapolis (and has that name today), the Emma Hanck turnpike. “Six miles from the city is a grocery and blacksmith shop, which may be used to good advantage by unfortunates.” This is between Morris Street and High School Road, which was called the Forsha Turnpike, which connected the National Road to Ben Davis Post Office. At seven miles from the city, a “pleasant resting place for the first riders” at a big saw mill. A dirt road near this point, running north and south, could allow a rider wanting a short ride to connect back to the city via “half a dozen turnpikes running east and west.”

At a point 9.5 miles from the city, where the road passes through a small, well shaded village called Bridgeport. The road then continues over White Lick Creek and rumbles toward Plainfield over what was a recent installment of fresh gravel. Finally, before leaving Marion County, the rider will come across a “large nursery, with green and white buildings and storehouses, situated on the side of a hill” just at the edge of the county line.

Bicycling the Crawfordsville Pike

Indianapolis News, 09 May 1896, map showing “the Crawfordsville Route.” It should be noted that the “PCC&StL” notations on this map along the railroad tracks from Indianapolis to Danville and Indianapolis to Crawfordsville should read “CCC&StL,” as these are Big Four (NYC) tracks, not Panhandle (PRR) tracks.

Keeping with the Indianapolis News articles about bicycling routes from the city, today we focus on the Crawfordsville Pike, from the News of 09 May 1896. For starters, the Crawfordsville Road was built in the 1820s as the Indianapolis-Crawfordsville Road. It wasn’t the straight route that exists today. Marion County’s section was covered here. Outside Marion County, what became the Peoria & Eastern/Big Four/New York Central was built to dart back and forth across the original road. This was typical of railroad companies at the time, since road travel was sketchy most of the time.

Editor’s note: For those unfamiliar with the work “pike” in this context, here goes. “Pike” is a shortened version of the word “turnpike,” which was a term used to describe a toll road. At points where a toll was to be paid, a large stick, or pike, was put across the road. Once the toll was paid, the toll collector would turn the pike, or move it out of the way for passage.

The bicycle route recommends following, from the Circle, Illinois north to Indiana, Indiana out to Michigan, and Michigan Street out to Haughville. “At the second street beyond the river bridge” the rider should turn north. This is now Belmont Avenue. Belmont took the rider to, and along side, the White River. At the time, the White River Parkway did not exist. Continuing north meant meeting the junction of the Crawfordsville and Lafayette Roads at what is now 16th and Lafayette, although the connection was moved south to allow replacement of the intersection in the 1950s. (Being the parts of US 52 and US 136 at the time, the state made the decision to revamp the area.) The area is shown on the map below. Best described in the News, the bicyclist should “turn and go to a point where the road forks, one branch running north and one west. The west fork is the Crawfordsville pike.”

1889 Map of the area of what is now 16th Street and Lafayette Road. Grandview Street at the bottom of the snippet is 10th Street today. Crawfordsville Gravel Road is 16th Street. The city limits line on the right runs through Belmont Avenue. The bridge over White River, called the Emricksville Bridge, connected the old Crawfordsville/Lafayette Road to downtown to the same roads west of the river. That bridge was named after owners of the land in the area. Image courtesy of the Indiana State Library Digital Collection.

From here, the original road followed what is now 16th Street out to Cunningham Road northwest to (just shy) of what is now Crawfordsville Road. From this point, the old road “runs close to the Peoria & Eastern tracks most of the distance to Brownsburg, passing through Clermont and crossing the tracks twice. This stretch of road is almost level. There are only two small hills.” After Brownsburg, the road is level to Pittsboro. “Any lover of beautiful scenery who is the happy possessor of a camera would do well to take the extra trouble” to bring that camera along.

This changed once past Pittsboro. “From Pittsboro the road is devoid of unusual features, with the exception of a rather long hill about a mile and a half before reaching Lizton.” The writer of this article actually had some advice about this particular hill. “A little caution should be observed in taking this hill, and none but those having accident policies, with all premiums paid, should attempt coasting.” I guess that’s subtle.

1909 map of northern Hendricks County showing the route of the Crawfordsville Pike from Brownsburg to the county line northwest of Lizton. Snippet courtesy of the Indiana State Library Digital Collection.

Here’s where a little historic research is needed. The News states that “the railroad is again crossed before reaching Lizton. From this town the road leads north about three-quarters of a mile, then forks. The west fork should be taken.” According to maps of the era, like the 1909 shown above, the railroad crossover is west of Lizton by one mile. And that crossover is just about 1/2 mile north of the turn in the road. The road then follows closely the railroad on the north side of the tracks. This continues to just before the Boone-Hendricks County Line southeast of Jamestown.

The road crosses back over to the south side of the P&E tracks before leaving Hendricks County. After Jamestown, the road gets “more hilly.” It is also stated that if you have your camera, “at Raccoon creek the camera ‘fiend’ may again find scenery worthy of his instrument.” Before entering Montgomery County, southeast of New Ross, the road once again crosses the railroad tracks. The road here is still in place, with the exception of the bridge over the Big Raccoon Creek. The described trip uses what is now State Street entering New Ross, and follows that street, and the county road continuing from there, to the current US 136. All this time, the road is north of the P&E tracks.

From New Ross to Crawfordsville the route curved quite a bit, before entering the Montgomery County seat. “Crawfordsville is quite a bicycle town, and contains many riders. The wheelmen make it a point to be very courteous to visiting riders.”

A big goal in the early days of bicycling is called “the Century,” a 100 mile trip in one day. The article goes on to mention that following the Crawfordsville Pike from Indianapolis to Crawfordsville and back “will give the rider almost a century.” The article also mentions a more hilly route back to Indianapolis via the Rockville road, which “will make a ride of 110 miles.”

US 36 in Indiana

Indiana has always been known as the “Crossroads of America.” For the most part, highways connecting Indiana to the rest of the United States have been through routes. But in the beginning of the US highway system (i.e. that on 1 October 1926, when it came to life in Indiana), there was one that ended near the western edge of the city of Indianapolis: US 36.

Let’s step back quite a bit before October 1926. What is now US 36 began life as the Indianapolis-Rockville State Road, basically a wagon trail connecting the capital city to the county seat of Parke County. Along the way, it also connected to the county seat of Hendricks County, Danville. What is currently US 36 west of Hendricks County is part of the original road. However, there were several sections that were straightened out by the state over the years.

When the Auto Route era started, the Rockville Road (now a series of county gravel roads) was included as part of the Pikes Peak Ocean to Ocean Highway. I have copies of maps spanning 1918 to 1920 showing this. Also, the Federal Highway Administration shows this in a series of strip maps. This link shows the section from Indianapolis to Chrisman, IL.: https://www.fhwa.dot.gov/infrastructure/ppmap05.cfm

(East of Indianapolis, at this time, the PPOO followed the National Old Trails Road, including the Eaton Cut-off, towards Dayton, OH.)

By 1923, the PPOO had moved, according to the website http://www.ppoo.org. The 1923 route was moved to come into Indiana along what was original SR 33 across Indiana. OSR 33 became SR 34 (and, later, US 136) from the Illinois-Indiana state line to Crawfordsville, then became SR 32 through Lebanon, Noblesville, Anderson, Muncie and Winchester to the Indiana-Ohio State Line at Union City.

The old PPOO, Rockville Road, by 1923, became SR 31 from SR 10 (future SR 63) to its connection with OSR 3 (the National Road) at what is now Holt Road and Washington Street. (To use the original road, either east or west, requires a journey through a Steak ‘n Shake parking lot. This is a fact that I have repeatedly used throughout the existence of both this blog and the Facebook group that spawned it.)

Indianapolis News, 27 September 1926.
The “Great Renumbering” is about to occur in Indiana.
This snippet shows the pending US 36 description.

With the Great Renumbering of 1 October 1926, US highways were added to the state, and US 36 was among them. The route of the original PPOO, the one that became SR 31, became the route of US 36. However, the section that connected Chrisman, IL, to SR 63 was incomplete and under construction. Since, at the time, it had not been a section of the state highway system, the ISHC was playing catch up to get it up to speed. Also, at the time, the original US 36 connected to the National Road at the above mentioned Steak ‘n Shake (i.e. Washington Street and Holt Road). Holt Road originally came from the south and ended at this intersection. It would be many years later, even after the removal of US 36 to I-465’s south leg, that Holt Road would be built to the dead end (more or less) that it is today.

Indianapolis News, 28 April 1928.
Signs posted by the ISHC at the corner of
Meridian and Washington Streets
in Indianapolis.

That’s right. US 36 ended in Indianapolis. It followed US 40 downtown, but most maps I have seen from the era aren’t detailed enough to show that. The only proof I have of that is a picture from the Indianapolis News of 28 April 1928. It shows a “highway totem pole” at the corner of West Washington Street and Meridian Street. (That point was a multiplex consisting, in the order the state put them, US 40, US 52, US 36 and SR 29. US 36 stayed in that status for at least the next five years.

I am doing further research into the location of US 36 along the Rockville Road/Rockville Avenue corridor. For the longest time, the section that is Rockville Road now from Washington Street to what is called Rockville Avenue didn’t exist. As a matter of fact, official Indiana State Highway Commission maps show that Rockville Avenue was US 36 all the way up to 1930. What is now Rockville Road east of Rockville Avenue, apparently was the dream of the E. L. Cothrell Realty Company. In 1925, they started building a new neighborhood, which could be reached by going “out West Washington street to the 3500 block.” By 1927, it would finally list the Rockville Road as part of the marketing, as all houses would front either Creston (the name of the development) or Rockville. As shown in the map below, it would seem that the “new” Rockville Road was built expressly for the Creston development.

Map, courtesy of Google Maps, showing the Rockville Road from Washington Street to the original road now called Rockville Avenue. Creston Drive, the main side street of the Creston development started in 1925 is shown, as well. (Map was captured using Microsoft Snipping Tool on 1 April 2019.

By 1932, the extension of US 36 started. The signs marking US 36 were extended along what was then SR 67 (Massachusetts Avenue/Pendleton Pike) and, when near Pendleton, along SR 9/SR 67 to Huntsville, where a road was authorized to connect Huntsville to Ohio SR 200 at the state line west of Palestine, OH. At that time, the designation US 36 entered Ohio as the cross state line continuation of SR 32 at Union City. That US 36 connected Union City to Greenville, OH.

Indiana State Highway Commission official 1932 map showing US 36 both at Pendleton and in Ohio from Union City to Greenville. The red dotted line from Huntsville east through Sulphur Springs, Mount Summitt, Mooreland to the JCT SR 21 south of Losantville, and the red dotted line from JCT SR 21 north of Losantville, east through Modoc and Lynn to connect OH SR 200 show the authorized route of the extension of US 36.

By 1933, the state had under its jurisdiction the complete route that would be US 36 in Indiana. There were some changes along the way, with sections moved and bypassed here and there. The first bypass was being built in 1935, which would be a replacement for the section through downtown Indianapolis. By 1936, US 36, and SR 67, would be turned north along SR 29 (later US 421, today West Street/Martin Luther King Jr. Street) to 38th Street. Then east along 38th Street to its connection to Pendleton Pike. (BTW – officially, this is the beginning of what is now called Pendleton Pike. 38th Street, at the time, was the edge of the city most of the way. As such, inside 38th Street, the old Pendleton Pike is called Massachusetts Avenue. That will be the subject of a later post…I promise.)

The major bypass would also be in Marion County. In the late 1970’s, the Indiana Highway Department, and its successor, the Indiana Department of Transportation, would start handing state roads back to the counties. In Marion County, as far as US 36 was concerned, that would mean that the designation US 36 would turn onto I-465, using the road from Rockville Road on the west side, along the south leg, to Pendleton Pike on the northeast side.

Indianapolis: Crossroads City

Originally published 24 March 2015.

When the Good Roads Movement started in the late 19th century, the primary focus was on, more or less, two things: bicycle transportation and mail delivery. Cars came later into the discussion.

Indianapolis was already a crossroads city. Unfortunately, most of that was eclipsed by being a major crossroads in the world of railroads. While you could get to the city using the trails at the time, Indianapolis really took off when the Madison & Indianapolis Railroad came to town. And to be honest, Indianapolis WAS a town until the railroad was built. 1847 not only marked the coming of the M&I, but the incorporation of the City of Indianapolis.

When the named highways started appearing on the scene, they naturally followed the paths that were already there. The major roads into Indianapolis became a hodge-podge of named routes linking the city to far away destinations.

But what WERE those roads before they became the Dixie, or the Jackson, or any other of the names. That is the purpose of this post.

The National Old Trails Road for 80 years had a shorter name here: the National Road. For those that don’t know, the National Road was built along its route to connect the (then) capital cities of Ohio, Indiana and Illinois. (The irony is that there STILL is a road to connect Indianapolis to the now capital of Illinois, it’s just not US 40, it’s US 36).

Pike’s Peak Ocean-to-Ocean: The original route from the west connects Indianapolis to Springfield, IL. (See above.) It came into town as the Rockville Road, leaving as the National Road to the east.

Dixie Highway: One route entered from the west along the Crawfordsville Road. The other route entered from the north along Indiana’s first state road, the Michigan Road. One route left the city along the Bluff Road (named for going to the bluffs of the White River at Waverly), the other, again, followed the National Road towards Richmond.

Jackson Highway: Entered from the northwest along the Lafayette Road, left southeast along the Madison Road.

Hoosier Highway: Entered from the northeast along the Oaklandon Turnpike (changed and shortened to Pendleton Pike), left southwest via the Mooresville Road.

Hill & Lake Trail: Entered from the north along the Fort Wayne (Allisonville) Road, left via the Three Notch Road.

Range Line: Entered from the north along the Range Line (Westfield) road, left south via the Madison road.

Some of you may notice that road names are still the same in some cases.