Original SR 31 and the Pike’s Peak Ocean-To-Ocean Highway

Just a short post to show how state roads have changed.

I have covered Auto Trails and the original state road numbers several times over the past nearly two years. I had done a post about the rerouting of the Pike’s Peak Ocean-To-Ocean Highway through Indiana. But the original route, as covered by fellow blogger (and ITH Facebook Group co-admin) Jim Grey, traveled across the western part of the state using the US 36 corridor. (The latest is “US 36 and the Pikes Peak Ocean-to-Ocean Highway in Danville, Indiana,” among others) I’d like to say it followed the current US 36, but it’s been moved several times over the years.

As I had mentioned in other posts along the way, many of the roads that were added originally to the state highway system were part of the Auto Trails systems that crossed the United States. When the Pike’s Peak road was taken into the state system, it was given the designation “State Road 31.” Well, sort of.

OSR 31 started in the west at OSR 10, across the Wabash River west of Montezuma. From there, it went through Montezuma, Rockville, and Bainbridge to Danville. From Danville, the PPOO rumbled across Hendricks and Marion Counties along what is now Rockville Road (and Rockville Avenue – because Rockville Road didn’t connect to Washington Street directly until later). The original SR 31, however, connected to the National Road (then Original State Road 3) at a completely different location.

Strangely, the route of the original SR 31 is now not part of the state highway system. Current SR 39 leaves Danville via Cross Street south towards Martinsville. Original State Road 31 turned south from Main Street on Jefferson Street. Jefferson Street turns into Blake Street, then Cartersburg Road. The state road connected to OSR 3 southeast of Cartersburg.

The drive from Danville to Cartersburg is quite a nice one.

With the Great Renumbering in October 1926, original state road 31 became US 36. Again, sort of. The section from Danville to Cartersburg was removed from the highway system at that time. US 36 continued on into Marion County, as shown in the article “Road Trip 1926: US 36.” Just like the original eastern end of OSR 31, the original eastern end of US 36 is now gone, ending at a parking lot.

I also covered a reroute that was put in place along US 36, after the Great Renumbering, at Bainbridge.

Marion County: Wall Street Pike

Today, I want to look at a road that most people wouldn’t know by the name. I will not share the name it has today until the end, so that I can keep my readers guessing throughout the article. But, suffice it to say, it is an important road on the westside of Marion County. It was also a toll road that led from the Crawfordsville Pike westward to the Hendricks County line. It would also keep the “Wall Street Pike” name until it was officially changed in 1968.

But I want to share a couple of stories about the road today.

Indianapolis Star, 7 July 1927. Wall Street Pike covered bridge over Eagle Creek burned to the ground.

In July 1927, a fire destroyed the Wall Street Pike covered bridge over Eagle Creek. The bridge according to the Indianapolis Star of 7 July 1927 was described thus: “After stubbornly fighting the onrush of civilization and modernity for more than sixty years, the covered bridge over Eagle Creek on the Wall street pike, about four and a half miles northwest of Indianapolis, was destroyed by fire yesterday afternoon.”

The Wall Street Pike Bridge was one of only four covered bridges left in Marion County at the time of the fire. The article goes on to locate the three remaining ones: White River near Southport, Indian Creek a short distance east of Fort Benjamin Harrison, and Williams Creek at 75th Street.

Arrival of the fire department, from Engine House #9 at 537 Belleview Place, was too late to save the structure. Before the first spray of water hit the bridge, it was was wavering on its foundation. It then fell into the creek. Hundreds of people watched as the bridge timbers sank into Eagle Creek. “The timbers seemed to recall the countless number of buggies, carriages, old farm wagons, oxen teams, pioneers on horseback, and others, that had passed over it since the day it was dedicated with speeches and music by the Indianapolis ‘town band.'”

The cost of the bridge, when it was built, was estimated at $15,000. It was estimated that it would cost three times that much to replace it in 1927 with the same materials. The structure had been built using black walnut and ash trees, often hewn by local farmers. Maintenance of the bridge, which mainly consisted of reflooring, had been done over time. The last time was about three weeks before the fire.

Wall Street Pike was closed for several weeks while a new $20,000 concrete bridge was built in the place of the old covered bridge. County commissioners would be asked to fund the new bridge…and the appropriation would be brought up at the next meeting.

“Until erection of the concrete bridge the open space between the banks of the stream where the old bridge once stood will reflect its memory and if creeks could talk, the waters would mourn the loss of a good, true and lasting friend.” (Source: Indianapolis Star, 7 July 1927)

The other story I wanted to share is that of the Pugh homestead. Jacob Pugh came to Marion County from Randolph County, North Carolina, in 1821, shortly after the creation of the county itself. He purchased hundreds of acres on the north side of the survey line that would become Wall Street Pike. A son-in-law purchased even more land to the northwest of Jacob Pugh. That land would later become Camp Dellwood.

Indianapolis Star, 20 December 1931.

The pictured house above was built by one of Jacob’s sons, Jesse, in 1846. It had been built from tulip wood. In the 1920’s, the house was sold to the Ashby family.

To tie this back to Indiana Transportation history, the beginning of the article in the Indianapolis Star. “Wall Street pike branches west from Crawfordsville road at the old toll gate which is still standing about six miles from the center of town. West from Eagle creek on this pike, which was one of the first gravel roads in this vicinity, stretches a double row of maple trees, forming a green avenue for about half a mile.”

Now comes the time I bring the Wall Street Pike into the present. From the public announcements in the Indianapolis Star of 9 March 1968 comes the following snippets:

“Pursuant to Section 20 of Chapter 283 of the Acts of the Indiana General Assembly for 1955, as amended by Chapter 380 of the Acts of the Indiana General Assembly for 1959, the Metropolitan Plan Commission of Marion County, Indiana, proposes the following Resolutions Establishing, Reestablishing or Changing The Names of Certain Streets in Marion County, Indiana:”

“68-ST-R-2 – That the name of the street presently known as WALL STREET PIKE from Cunningham Road continuing west to W. County Line Road, is hereby changed to, established as and will hereafter be designated as W. 21ST STREET.”

A Quick Look At Today’s State Roads, From A Historical View

A Facebook direct message from a reader of the blog started the research bug going again. Now, while I am still looking up information on his particular subject (transportation to Center Valley in Hendricks County, particularly a possible railroad there), part of his subject did come up. As well as a few others. Today, I want to look at the things that I have found while researching that topic…while not finding much about the topic.

The “town” of Center Valley is along the route that would become State Road 39 just north of the Morgan-Hendricks line. A post office existed there from 1855 to 1902. But what is important is the route that rumbles north to south through the town…the aforementioned SR 39. It wouldn’t be until 1932 when that section of SR 39 was added to the state highway system. But, the designation “state road” goes back quite a bit…like 1833.

The 17th General Assembly of Indiana passed into law several state roads. The first I want to mention would be the one that would make Center Valley (or, more to the point Centre Valley) a place. The route that would eventually become SR 39 was built as the Martinsville-Danville-Frankfort State Road. The southern end would be part of the state highway system from 1920 – the bridge over White River west of Martinsville. The northern end would be part of original State Road 6, connecting Lebanon to Frankfort. As original SR 6, it would become SR 39 with the Great Renumbering.

Two more state roads would from Martinsville would be added to Indiana with this meeting of the General Assembly. The first is one that would not become part of the state highway system. It was described as “an act to locate a state road from Martinsville, in the county of Morgan, by the way of Cox’s mill and Solomon Dunagan’s, in said Morgan county, to Stilesville, in the county of Hendricks.” This is an example of how the General Assembly would set up a “state road” through a particular person’s land. I would assume that what is now Tudor Road, southeast of Stilesville, was part of this road.

Another state road project including Martinsville did make it to the state highway system… eventually. The act created “a state road from Martinsville, in Morgan County, to intersect the state road leading from Madison to Indianapolis, at Edinburgh, in Johnson county by the way of Morgantown in said Morgan county.” This state road would be added back into the state highway system in the 1930’s…as State Road 252. A history of that road is available from ITH here.

But Martinsville wasn’t the only beneficiary of that particular meeting of the General Assembly.

A state road was created by the General Assembly to connect the town of Lagrange, in Tippecanoe County, to Logansport, in Cass County. Where is LaGrange? Well, it was a town along the Wabash River at the Warren-Tippecanoe County line. It was founded by Isaac Shelby in 1827…and had a post office from 1832 to 1835. It’s prime was with the Wabash Canal during the riverboat era. When the Wabash Railroad was built on the opposite side of the Wabash River, the town of LaGrange just dried up and disappeared.

Another road that was created at that time would connect Williamsport to the Illinois-Indiana State line via Lebanon (sic), now West Lebanon, and the now abandoned town of Chesapeake (about two miles east of Marshfield). This route will require some research.

Part of the road that would become, in time, SR 46 between Newbern and Bloomington would be added as a state road in 1833. The original road would start at the Michigan Road in Napoleon, travel through Camden (unknown today), Newbern, and Columbus to Bloomington. The section from Newbern to Columbus was part of the state highway system as SR 46, until INDOT truncated SR 9, turning the old SR 9 into SR 46.

Stilesville would be mentioned again as a state road was created to connect it to Crawfordsville via New Maysville.

The last road for this article would be a road that is still in existence, more or less, but not part of the modern state highway system. The description of the act was “to locate a state road from Green Castle, in Putnam county, to Carlisle, in Sullivan county, by way of Manhattan in Putnam county and Bowlingreen and New Brunswick, in Clay county.” Some day, I want to do more research on this road.

US 40: Bridgeport to Plainfield

When the National Road was surveyed in the 19th century, the people that laid out the road had very little to worry about when it came to man made obstructions to its path. The road was built in the most efficient way possible. Not necessarily the straightest, but the most efficient. An example of this is just west of downtown Indianapolis with the National Road bridge. The original route crossed the White River at a 90 degree angle…typical of bridge building at the time. And although that bridge would be later supplemented, then replaced, by a straighter Washington Street bridge, the old bridge would survive until 1904…a little over 70 years.

Another section of the old National Road that would survive into the 20th century before getting the straightening treatment would be the section starting just west of Bridgeport, heading toward Plainfield. Here, for two and half miles, the National Road would first curve its way across a creek, then find its way, in 1852, across a dangerous railroad crossing near the Marion-Hendricks County line.

Let’s start with the railroad crossing. In 1850, the Terre Haute & Richmond Railroad was chartered to create a route between its two title cities through Indianapolis. Typical railroad construction involves laying out the route to be as flat as possible. Through most of Indiana, being that most of the terrain is relatively flat, this is not a problem. The routing of the the TH&R west of Plainfield found itself winding through some very hilly territory. At Plainfield, the road started on a straight path to the Hoosier capital. When construction was completed in 1852 to Indianapolis, the railroad was a very straight line from west of Plainfield to Indianapolis.

Railroad construction at the time also didn’t take into consideration the roads that were in place when they were built. One half mile west of the Marion-Hendricks County line, at a spot that would later become known as Six Points, the TH&R was built to have a very flat crossing of the National Road. A crossing of about 15 degrees. On a clock, that is about the angle from 12:00 to 12:02:30, or half way between 2 and 3 minutes. Given the little amounts of traffic, the speed of trains, and what little there was normally involved horses, this was not seen as a problem.

Fast forward to the Auto Trail era when automobiles were taking over. Train traffic was booming, locomotive speeds were much higher, and the traffic was getting clogged with cars and trucks. The crossing at Six Points became one of the most dangerous in the state. With the state takeover of the old National Road as Original State Road 3 in 1917, the Indiana State Highway Commission became responsible for the conditions of both the road and the railroad crossing at this point. As traffic increased, this dangerous situation would remain into the mid-1930’s, when the ISHC started turning what had become US 40 into a divided highway across the entire state. The routing of US 40 curved to the north of the old road, crossing the Hendricks County Road (later to become 1050 East) a little over .1 mile north of the old crossing. The railroad, by this time the Pennsylvania Railroad, was then crossed at a 30 degree angle three tenths of a mile west of the Six Points Road.

This improved the situation at the crossing…but didn’t fix it completely. There were news stories of crashes, sometimes fatal, between cars and trains at that crossing, as well. But it did improve the situation.

The other quirk in the National Road would be the crossing of the creek at the west edge of Bridgeport. Bridgeport was an old village, mainly started as a watering hole along the old National Road. It is located less than 1/2 mile east of the Marion-Hendricks County line. At the west edge of town, the National Road curved slightly north of its straight path to cross over the White Lick Creek. The road then turned to become a straight line again aiming towards Plainfield.

This Google Map snippet shows the property lines of the old National Road from a point west of Raceway Road to west of Bridgeport. The road labelled “Old Washington Street” is the original path of the National Road/US 40.
This MapIndy aerial photograph, taken in 1941, shows the construction of the new US 40 west of Bridgeport.

When the state started working on connecting the two sections of already widened US 40, the section that remained was through Bridgeport and over the White Lick Creek Bridge. The work started on this section in 1941. The first task was to eliminate the curve at the White Lick Creek, making a straight line road between the 1936 bypass of Six Points and Bridgeport. It was mentioned in the Indianapolis News of 7 July 1941 that traffic through Bridgeport had dropped quite a bit with the old National Road/US 40 being closed for this construction. By 1942, the new section of US 40 would be completed, and the old road was left to flounder in the weeds.

Rockville State Road, US 36, near Bainbridge

When the original state roads were built, the state of Indiana created a road that connected Indianapolis to Rockville, via Danville. That road, still known today as Rockville Road in Marion County, is almost as straight as any road can get in this state. However, there were places where straight just wasn’t possible. Such a place is in Putnam County.

It should be noted that there were two things at play when it came to the building of the original state roads. First, the construction was done to keep costs to a minimum. There was no need to cat a path through a hill when one could just go around it. Path of least resistance was the motto of the day. Second, as a general rule, the state didn’t tend to take people’s property to build a road that would just be turned over to the county after it was built. This is one of the reasons that a road connecting two towns in early Indiana didn’t always go directly between two points. While it isn’t as noticeable on maps today, a quick glance at older maps shows the curvy way someone got from point A to point B in the early days of the state.

The Rockville State Road was (mostly) built along a section line, meaning very little property would have to be taken to create it. Generally, property lines in Indiana tend to work along the survey lines. Survey line separate townships, ranges and sections. Most of the time, property was purchased in one section or another, usually not crossing the section line. But there were several places that the old road did have to venture off of the survey lines beaten path.

One was east of Danville. Main Street through the city was the original Rockville State Road. When a short bypass between Danville and Avon was built, the old road was kept in place, but turned slightly at both the western and eastern ends. The following Google Map snippet shows the old property lines when it came to the western (Danville) end of old Main Street/SR 31/US 36. Main Street turns southwest, while the old property lines turn due west to connect to Danville itself.

The other section was a much larger bypass built by the state in 1933. East of Bainbridge, the old state road took a dive to the south of the survey line…sometimes venturing almost a mile south of the line itself. The following map is from 1911, showing the postal routes that were followed at that time, and showing the old Rockville State road in its original alignment.

As shown on the map, going west to east, the old road started turning southeastward in Section 12, continuing further southeast in Section 7, and hitting its southern most point in Section 8. From there, it worked its way back northeastward until it reached the section line again in Section 10. This created a variance from the section line that was nearly four miles long.

Editor’s Note: As is typical of the original surveys, sections along the western edge of the range [sections 6, 7, 18, 19, 30 and 31] are smaller than one mile wide. The Range Line between those sections listed above, and sections 1, 12, 13, 24, 25 and 36 of the range west, is known as a correction line. This can be spotted throughout the state, not only by the less than one mile wide sections, but the occasional deviance from a straight line going west to east. In Marion County, Shelby Street and Franklin Road are those correction lines…and looking at the roads crossing them shows the correction. The survey line along the north edge of the map is the township line, separating survey townships 15 North and 16 North. Following that line to the east, it becomes part of the Danville State Road in eastern Hendricks County, 10th Street (the geographic center) through Marion County, and the numbering center of Hancock County. It is also a correction line in the surveys, so sometimes survey lines jog a bit when crossing it as well.

This section of the old road was very curvy, narrow, and did not lend itself well to the pending explosion of traffic that would be coming its way with the creation of the Auto Trails and, later, the State Highway System. When the Pike’s Peak Ocean to Ocean highway was created, it followed the old Rockville Road from Rockville to Indianapolis. Thus, it followed this curvy, winding line through Putnam County.

Things would change in 1933, when the Indiana State Highway Commission announced that construction would begin on US 36 from Danville to Bainbridge. This project would complete the straightening of the federal highway from west of Indianapolis to the Illinois-Indiana State Line. The Indianapolis Star of 1 April 1933 reported “a twenty-five mile detour from Danville to Bainbridge on United States Road 36 over pavement and dustless type road has been established to take care of traffic pending completion of new pavement between Danville and Bainbridge which will complete the project from Indianapolis to the Illinois state line.”

The above Google map snippet shows the exact same area as covered by the 1911 USPS map shown above. The route of US 36 through the area, shown in yellow, is the 1933 bypass built by the ISHC. The old road is still very narrow and winding, but still can be traveled to this day. The Indiana Official Highway map of 1933 shows the new road under construction, with the old road removed from the map. By the time the next official map was released for June 1934, the new road was completed and opened. The following is the 1936 survey map of Putnam County roads, including road width, constructing materials and bridge of the same area.

The new roadway included bridges marked as AS, AT, and AU on this map. The old road included CN, CM, CH, CG, and CK. (Note, they are marked on the map in lower case letters. I am using upper case to denote them since it is easier to read.) Both AS and AU were built 24 feet wide, while AT was built 20 feet wide. All three had a safe working load of 20 tons.

The old road’s bridges were a bit more complicated. CN was 12.7 feet high, 12.7 feet wide, and had a safe working load of three tons. CK was 16 feet wide and could handle 15 tons. CM was 19.5 feet wide, with a working limit of 20 tons. This would make it almost equal to the bridge that replaced it (AT), only being six inches narrower with the same work load limit. Both CG and CH were 20 feet wide with a 20 ton safe load limit.

The old road, according to the figures on the 1936 map, had a right-of-way 40 feet wide. The new US 36 through the area had a right-of-way of 60 feet in width. Most of the county roads in the area had a right-of-way narrower than the old Rockville State Road, usually less than 10 feet.

The other part of this realignment project was through Bainbridge itself. The old road traversed the town along Main Street. The new road bypassed Main Street to the north…by only one block. It still does to this day.

Jim Grey, on his old web site, covers the sections of the old road that connect to the current US 36 fairly well. That page is at: http://www.jimgrey.net/Roads/US36West/04_Bainbridge.htm. I think I have read somewhere that this website will be migrated over to his WordPress blog, “Down The Road.” If this is the case, get it while you can. And who knows, maybe after all the “stay at home” mess is over, I might make a trip out to this section of the old road to take some onsite surveys. (I would love to say take pictures…but my lack of photography skills is only surpassed by my complete lack of patience to take the time to make them good. Not gonna lie here, folks.)

Bicycling the Crawfordsville Pike

Indianapolis News, 09 May 1896, map showing “the Crawfordsville Route.” It should be noted that the “PCC&StL” notations on this map along the railroad tracks from Indianapolis to Danville and Indianapolis to Crawfordsville should read “CCC&StL,” as these are Big Four (NYC) tracks, not Panhandle (PRR) tracks.

Keeping with the Indianapolis News articles about bicycling routes from the city, today we focus on the Crawfordsville Pike, from the News of 09 May 1896. For starters, the Crawfordsville Road was built in the 1820s as the Indianapolis-Crawfordsville Road. It wasn’t the straight route that exists today. Marion County’s section was covered here. Outside Marion County, what became the Peoria & Eastern/Big Four/New York Central was built to dart back and forth across the original road. This was typical of railroad companies at the time, since road travel was sketchy most of the time.

Editor’s note: For those unfamiliar with the work “pike” in this context, here goes. “Pike” is a shortened version of the word “turnpike,” which was a term used to describe a toll road. At points where a toll was to be paid, a large stick, or pike, was put across the road. Once the toll was paid, the toll collector would turn the pike, or move it out of the way for passage.

The bicycle route recommends following, from the Circle, Illinois north to Indiana, Indiana out to Michigan, and Michigan Street out to Haughville. “At the second street beyond the river bridge” the rider should turn north. This is now Belmont Avenue. Belmont took the rider to, and along side, the White River. At the time, the White River Parkway did not exist. Continuing north meant meeting the junction of the Crawfordsville and Lafayette Roads at what is now 16th and Lafayette, although the connection was moved south to allow replacement of the intersection in the 1950s. (Being the parts of US 52 and US 136 at the time, the state made the decision to revamp the area.) The area is shown on the map below. Best described in the News, the bicyclist should “turn and go to a point where the road forks, one branch running north and one west. The west fork is the Crawfordsville pike.”

1889 Map of the area of what is now 16th Street and Lafayette Road. Grandview Street at the bottom of the snippet is 10th Street today. Crawfordsville Gravel Road is 16th Street. The city limits line on the right runs through Belmont Avenue. The bridge over White River, called the Emricksville Bridge, connected the old Crawfordsville/Lafayette Road to downtown to the same roads west of the river. That bridge was named after owners of the land in the area. Image courtesy of the Indiana State Library Digital Collection.

From here, the original road followed what is now 16th Street out to Cunningham Road northwest to (just shy) of what is now Crawfordsville Road. From this point, the old road “runs close to the Peoria & Eastern tracks most of the distance to Brownsburg, passing through Clermont and crossing the tracks twice. This stretch of road is almost level. There are only two small hills.” After Brownsburg, the road is level to Pittsboro. “Any lover of beautiful scenery who is the happy possessor of a camera would do well to take the extra trouble” to bring that camera along.

This changed once past Pittsboro. “From Pittsboro the road is devoid of unusual features, with the exception of a rather long hill about a mile and a half before reaching Lizton.” The writer of this article actually had some advice about this particular hill. “A little caution should be observed in taking this hill, and none but those having accident policies, with all premiums paid, should attempt coasting.” I guess that’s subtle.

1909 map of northern Hendricks County showing the route of the Crawfordsville Pike from Brownsburg to the county line northwest of Lizton. Snippet courtesy of the Indiana State Library Digital Collection.

Here’s where a little historic research is needed. The News states that “the railroad is again crossed before reaching Lizton. From this town the road leads north about three-quarters of a mile, then forks. The west fork should be taken.” According to maps of the era, like the 1909 shown above, the railroad crossover is west of Lizton by one mile. And that crossover is just about 1/2 mile north of the turn in the road. The road then follows closely the railroad on the north side of the tracks. This continues to just before the Boone-Hendricks County Line southeast of Jamestown.

The road crosses back over to the south side of the P&E tracks before leaving Hendricks County. After Jamestown, the road gets “more hilly.” It is also stated that if you have your camera, “at Raccoon creek the camera ‘fiend’ may again find scenery worthy of his instrument.” Before entering Montgomery County, southeast of New Ross, the road once again crosses the railroad tracks. The road here is still in place, with the exception of the bridge over the Big Raccoon Creek. The described trip uses what is now State Street entering New Ross, and follows that street, and the county road continuing from there, to the current US 136. All this time, the road is north of the P&E tracks.

From New Ross to Crawfordsville the route curved quite a bit, before entering the Montgomery County seat. “Crawfordsville is quite a bicycle town, and contains many riders. The wheelmen make it a point to be very courteous to visiting riders.”

A big goal in the early days of bicycling is called “the Century,” a 100 mile trip in one day. The article goes on to mention that following the Crawfordsville Pike from Indianapolis to Crawfordsville and back “will give the rider almost a century.” The article also mentions a more hilly route back to Indianapolis via the Rockville road, which “will make a ride of 110 miles.”